Tutorials Mill Level 1 Training - TechEdu.com

More documents

Recommendations

Info

Mill Level 1 TUTORIAL 723.3 Set the Cut ParametersFrom the Tree view list, select the Cut Parameters and change the parameters as shown.Compensation type set to Computer allows Mastercam to compensate the toolpath basedon the tool diameter and does not output G41/G42 in the code.Compensation direction set to Left compensates the toolpath to the left of the chain in theCCW direction.Tip Comp set to the Tip sets the tool offset to the tool tip.Entry/exit arc sweep set to 90 degrees makes a line between the plunge point and theentry/exit arc movement of a ¼ of a circle, at each entry/exit. See the picture below.Overlap sets how far the tool goes past the end of the toolpath before exiting. This ensures aclean finish.Entry/exit arc sweep set to 90 degreesPage 7-73
Mill Level 1 TUTORIAL 7From the Tree view list, select Roughing to add roughing passes to completed machine the inside ofthe hole.Enable Roughing and set the parameters as shown.Circle mill roughing creates roughing passes using tangent arcs. The result provides asmooth motion for the tool, a short NC program, and good cleanout.Stepover is set as a percentage of the tool diameter.Helical entry parameters create the roughing motion tangent to a helical entry.Output arc moves generates arc movements instead of small linear moves which make theprogram smaller.From the Tree view list, select Depth Cuts and set the parameters as shown.Depth cuts set the cuts along the Z-axis. Mastercam divides the total depth into equalsteps based on the Max rough step value.Keep tool down enabled doesn’t allow the tool to retract between cuts.Page 7-74
Page 2:
Mill Level 1 Training TutorialsToor
Page 6:
TUTORIALSERIESFORHOWTOUSETHISBOOKTh
Page 9 and 10:
TUTORIAL SERIES FORTUTORIAL #7LEVEL
Page 12 and 13:
Mill Level 1 TUTORIAL 7GEOMETRY CRE
Page 14 and 15:
Mill Level 1 TUTORIAL 7During the g
Page 16 and 17:
Mill Level 1 TUTORIAL 7Select the A
Page 18 and 19:
Mill Level 1 TUTORIAL 7[ Select a l
Page 20 and 21:
Mill Level 1 TUTORIAL 74.3 Remove p
Page 22 and 23:
Mill Level 1 TUTORIAL 7STEP 5: CREA
Page 24 and 25:
Mill Level 1 TUTORIAL 75.2 Creating
Page 26 and 27:
Mill Level 1 TUTORIAL 75.4 Creating
Page 28 and 29:
Mill Level 1 TUTORIAL 7Select the T
Page 30 and 31:
Mill Level 1 TUTORIAL 7[ Select ent
Page 32 and 33: Mill Level 1 TUTORIAL 7The final ge
Page 34 and 35: Mill Level 1 TUTORIAL 7STEP 8: SELE
Page 36 and 37: Mill Level 1 TUTORIAL 7Select the O
Page 38 and 39: Mill Level 1 TUTORIAL 7Select the l
Page 44 and 45: Mill Level 1 TUTORIAL 710.5 Set the
Page 46 and 47: Mill Level 1 TUTORIAL 7Click on the
Page 48 and 49: Mill Level 1 TUTORIAL 7Select the R
Page 50 and 51: Mill Level 1 TUTORIAL 7Copy the geo
Page 54 and 55: Mill Level 1 TUTORIAL 713.2 Modify
Page 56 and 57: Mill Level 1 TUTORIAL 7Select the P
Page 58 and 59: Mill Level 1 TUTORIAL 7Initial stoc
Page 60 and 61: Mill Level 1 TUTORIAL 7STEP 16: CRE
Page 62 and 63: Mill Level 1 TUTORIAL 7Select Top V
Page 64 and 65: Mill Level 1 TUTORIAL 7STEP 18: FAC
Page 66 and 67: Mill Level 1 TUTORIAL 7From the Tre
Page 68 and 69: Mill Level 1 TUTORIAL 719.2 Select
Page 70 and 71: Mill Level 1 TUTORIAL 7From the ext
Page 78 and 79: Mill Level 1 TUTORIAL 7Select only
Page 90 and 91: Mill Level 1 TUTORIAL 7STEP 26: VER
Page 92: Mill Level 1 TUTORIAL 7Select the r
Page 96 and 97: Mill Level 1 TUTORIAL 7Student prac
Page 98: Mill Level 1 TUTORIAL 7TUTORIAL 7 Q
show all

Tutorials Mill Level 1 Training - TechEdu.com

Create successful ePaper yourself

Delete template?

Save as template?