TM-U295/U295P

More documents

Recommendations

Info

<strong>TM</strong>-<strong>U295</strong>P Switch Function ON OFF 1 Auto-line feed Normally enabled Normally disabled 2 Receive buffer capacity 35 bytes 512 bytes 3 Undefined 4 Undefined 5 Undefined 6 Undefined 7 Undefined 8 Undefined 9 Undefined 10 Reserved. Setting must not be changed Note: If you change any DIP switch settings while the printer is turned on, the new settings will not take effect until you turn the printer off and back on or reset it. Installation 1-17
Chapter 2 Using the Printer The control panel has three buttons and three lights. Buttons RELEASE REVERSE All three of these buttons can be disabled or enabled by the ESC c 5 command. Pressing this button moves the rollers so that paper can be inserted or removed. Feeds the paper backward based on the line feed amount set by ESC 2 and ESC 3. FORWARD Feeds the paper forward based on the line feed amount set by ESC 2 and ESC 3. You can also use the RELEASE button to start a self test. See Chapter 1 for details. Indicator Lights POWER This light is on whenever power is supplied to the printer. Using the Printer 2-1
Page 1 and 2: TM-U295/U295P Operator’s Manual U
Page 3 and 4: Printer parts (1) Upper case (2) Pr
Page 5 and 6: FCC CLASS A FCC Compliance Statemen
Page 7 and 8: DECLARATION of CONFORMITY for CE MA
Page 9 and 10: About This Manual Setting Up and Us
Page 11 and 12: Chapter 5 Commands Command Notation
Page 13 and 14: Removing the Transportation Damper
Page 15 and 16: 2. Connect the other end of the cab
Page 17 and 18: Den Drucker an die Lade anschließe
Page 19 and 20: Connecting the Power Supply This pr
Page 21 and 22: CAUTION: Be sure to perform the ste
Page 23 and 24: 8. To put the cover back on the pri
Page 25 and 26: 3. While holding down the RELEASE b
Page 27: TM-U295 Switch Function ON OFF 1 Da
Page 31 and 32: Then remove the used ribbon by gras
Page 33 and 34: Chapter 4 Reference Information Pri
Page 35 and 36: Paper Specifications Paper type: To
Page 37 and 38: Printing position NOTE 1. Mechanica
Page 39 and 40: EMI and Safety Standards EMI standa
Page 41 and 42: Chapter 5 Commands Command Notation
Page 43 and 44: [Description] Prints the data in th
Page 45 and 46: Bit Off/On Hex Decimal Function 3 O
Page 47 and 48: [Description] Sets the character sp
Page 49 and 50: • d is the dot data for the chara
Page 51 and 52: ESC ✽ m nL n H [d]k [Name] Select
Page 53 and 54: Hex 1B 3D n Decimal 27 61 n [Range]
Page 55 and 56: [Notes] • Up to 32 tab positions
Page 57 and 58: [Default] [Reference] Double-densit
Page 59 and 60: dx = [dxL + dxH ✕ 256] dy = [dyL
Page 61 and 62: [Range] 0 ≤ n ≤ 255 [Descriptio
Page 63 and 64: [Description] Sets the time that th
Page 65 and 66: • When Auto Status Back (ASB) is
Page 67 and 68: [Description] Turns upside-down pri
Page 69 and 70: Bit Off/On Hex Decimal Status for A
Page 71 and 72: Third byte (paper sensor informatio
Page 73 and 74: • When Auto Status Back (ASB) is

TM-U295/U295P

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?