TM-U295/U295P

More documents

Recommendations

Info

RELEASE This light is on when the printer is in the paper release mode and it is off when the printer is in the clamp mode. Paper can be inserted only when the printer is in the paper release mode. This light blinks to indicate an error condition in the following cases: ❏ ❏ ❏ ❏ ❏ Paper jam Home position error Timing error Drive circuit error Power supply voltage error If this light blinks, turn off the printer, make sure that no paper is jammed in it, and then turn it back on. If the light is still blinking, contact a qualified service person. PAPER OUT This light is on when paper is not inserted or is not inserted correctly. Replacing a Used Ribbon When your printing is not dark enough, it is time to replace the ribbon. First follow steps 1 through 4 in the “Installing the Ribbon” in Chapter 1. 2-2 Using the Printer
Then remove the used ribbon by grasping the handle and pulling straight out, as shown by the arrow in the illustration below. Then follow the rest of the steps in “Installing the Ribbon” in Chapter 1. Using the Printer 2-3
Page 1 and 2: TM-U295/U295P Operator’s Manual U
Page 3 and 4: Printer parts (1) Upper case (2) Pr
Page 5 and 6: FCC CLASS A FCC Compliance Statemen
Page 7 and 8: DECLARATION of CONFORMITY for CE MA
Page 9 and 10: About This Manual Setting Up and Us
Page 11 and 12: Chapter 5 Commands Command Notation
Page 13 and 14: Removing the Transportation Damper
Page 15 and 16: 2. Connect the other end of the cab
Page 17 and 18: Den Drucker an die Lade anschließe
Page 19 and 20: Connecting the Power Supply This pr
Page 21 and 22: CAUTION: Be sure to perform the ste
Page 23 and 24: 8. To put the cover back on the pri
Page 25 and 26: 3. While holding down the RELEASE b
Page 27 and 28: TM-U295 Switch Function ON OFF 1 Da
Page 29: Chapter 2 Using the Printer The con
Page 33 and 34: Chapter 4 Reference Information Pri
Page 35 and 36: Paper Specifications Paper type: To
Page 37 and 38: Printing position NOTE 1. Mechanica
Page 39 and 40: EMI and Safety Standards EMI standa
Page 41 and 42: Chapter 5 Commands Command Notation
Page 43 and 44: [Description] Prints the data in th
Page 45 and 46: Bit Off/On Hex Decimal Function 3 O
Page 47 and 48: [Description] Sets the character sp
Page 49 and 50: • d is the dot data for the chara
Page 51 and 52: ESC ✽ m nL n H [d]k [Name] Select
Page 53 and 54: Hex 1B 3D n Decimal 27 61 n [Range]
Page 55 and 56: [Notes] • Up to 32 tab positions
Page 57 and 58: [Default] [Reference] Double-densit
Page 59 and 60: dx = [dxL + dxH ✕ 256] dy = [dyL
Page 61 and 62: [Range] 0 ≤ n ≤ 255 [Descriptio
Page 63 and 64: [Description] Sets the time that th
Page 65 and 66: • When Auto Status Back (ASB) is
Page 67 and 68: [Description] Turns upside-down pri
Page 69 and 70: Bit Off/On Hex Decimal Status for A
Page 71 and 72: Third byte (paper sensor informatio
Page 73 and 74: • When Auto Status Back (ASB) is

TM-U295/U295P

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?