TM-U295/U295P

More documents

Recommendations

Info

Bit Off/On Hex Decimal Status for ASB 6 Off 00 0 Undefined. On 40 64 Undefined. 7 Off 00 0 Not used. Fixed to Off. Bit 1: • Becomes On (slip printing possible) when slip paper is detected and becomes Off (slip printing is not possible) when slip ejection starts or time-out. • When the printer goes to the slip wait status, bit 5 and 6 of the third byte are On (no paper) and bit 1 of the forth byte is On (slip printing is not possible). • When paper-end stop is disabled by ESC c 4, bit 1 does not become On (slip printing is not possible) even if no printing area remains. • When the release button is pressed during slip printing, bit 1 becomes On (slip printing is not possible). [Default] n = 0 [Reference] DLE EOT, ESC u, ESC v GS r n [Name] Transmit status [Format] ASCII GS r n Hex 1D 72 n Decimal 29 114 n [Range] 1 ≤ n ≤ 2, 49 ≤ n ≤ 50 [Description] Transmits the status specified by n as, follows: n Function 1, 49 Transmits paper sensor status (same as ESC v) 2, 50 Transmits drawer kick-out connector status (same as ESC u 0) [Notes] • When DTR/DSR control is selected, the printer transmits only 1 byte after confirming the host is ready to receive data (DSR signal is SPACE). If the host computer is not ready to receive data (DSR signal is MARK), the printer waits until the host is ready. When XON/XOFF control is selected, the printer transmits only 1 byte without confirming the condition of the DSR signal. • This command is executed when the data in the receive buffer is developed. Therefore, there may be a time lag between receiving this command and transmitting the status, depending on the receive buffer status. 5-32 Commands
• When Auto Status Back (ASB) is enabled using GS a, the status transmitted by GS r and the ASB status must be differentiated. • If the value of n is out of the specified range, the printer ignores this command. • The status types to be transmitted are shown below: Paper sensor status (n = 1, 49): Bit Off/On Hex Decimal Status for ASB 0 1 2 3 Off 00 0 Slip is detected by BOF sensor. On 01 1 Slip is not detected by BOF sensor. Off 00 0 Slip is detected by TOF sensor On 02 2 Slip is not detected by TOF sensor. Off 00 0 Undefined. On 04 4 Undefined. Off 00 0 Undefined. On 08 8 Undefined. 4 Off 00 0 Not used. Fixed to Off. 5 6 Off 00 0 Undefined. On 20 32 Undefined. Off 00 0 Undefined. On 40 64 Undefined. 7 Off 00 0 Not used. Fixed to Off. Drawer kick-out connector status (n = 2, 50): Bit Off/On Hex Decimal Status for ASB 0 1 2 3 Off 00 0 Drawer kick-out connector pin 3 is LOW. On 01 1 Drawer kick-out connector pin 3 is HIGH. Off 00 0 Undefined. On 02 2 Undefined. Off 00 0 Undefined. On 04 4 Undefined. Off 00 0 Undefined. On 08 8 Undefined. Commands 5-33
Page 1 and 2:
TM-U295/U295P Operator’s Manual U
Page 3 and 4:
Printer parts (1) Upper case (2) Pr
Page 5 and 6:
FCC CLASS A FCC Compliance Statemen
Page 7 and 8:
DECLARATION of CONFORMITY for CE MA
Page 9 and 10:
About This Manual Setting Up and Us
Page 11 and 12:
Chapter 5 Commands Command Notation
Page 13 and 14:
Removing the Transportation Damper
Page 15 and 16:
2. Connect the other end of the cab
Page 17 and 18:
Den Drucker an die Lade anschließe
Page 19 and 20:
Connecting the Power Supply This pr
Page 21 and 22: CAUTION: Be sure to perform the ste
Page 23 and 24: 8. To put the cover back on the pri
Page 25 and 26: 3. While holding down the RELEASE b
Page 27 and 28: TM-U295 Switch Function ON OFF 1 Da
Page 29 and 30: Chapter 2 Using the Printer The con
Page 31 and 32: Then remove the used ribbon by gras
Page 33 and 34: Chapter 4 Reference Information Pri
Page 35 and 36: Paper Specifications Paper type: To
Page 37 and 38: Printing position NOTE 1. Mechanica
Page 39 and 40: EMI and Safety Standards EMI standa
Page 41 and 42: Chapter 5 Commands Command Notation
Page 43 and 44: [Description] Prints the data in th
Page 45 and 46: Bit Off/On Hex Decimal Function 3 O
Page 47 and 48: [Description] Sets the character sp
Page 49 and 50: • d is the dot data for the chara
Page 51 and 52: ESC ✽ m nL n H [d]k [Name] Select
Page 53 and 54: Hex 1B 3D n Decimal 27 61 n [Range]
Page 55 and 56: [Notes] • Up to 32 tab positions
Page 57 and 58: [Default] [Reference] Double-densit
Page 59 and 60: dx = [dxL + dxH ✕ 256] dy = [dyL
Page 61 and 62: [Range] 0 ≤ n ≤ 255 [Descriptio
Page 63 and 64: [Description] Sets the time that th
Page 65 and 66: • When Auto Status Back (ASB) is
Page 67 and 68: [Description] Turns upside-down pri
Page 69 and 70: Bit Off/On Hex Decimal Status for A
Page 71: Third byte (paper sensor informatio
show all

TM-U295/U295P

Create successful ePaper yourself

Delete template?

Save as template?