TM-U295/U295P

More documents

Recommendations

Info

•7 × 7 font when the dot pattern for code 32 (20H) is defined as shown below: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 MSB LSB ASCII code ESC & y c1 c2 x p1 p2 p3 p4 p5 p6 p7 Hex code 1B 25 01 20 20 07 1E 20 48 80 48 20 1E 5-10 Commands
ESC ✽ m nL n H [d]k [Name] Select bit-image mode [Format] ASCII ESC ✽ nL nH [d]k Hex 1B 2A nL nH [d]k Decimal 27 42 nL nH [d]k [Range] m = 0, 1 0 ≤ nL ≤ 255 0 ≤ nH ≤ 3 0 ≤ d ≤ 255 k = nL + nH x 255 [Description] Selects a bit-image mode using m for the number of dots specified by nL and nH, as follows: Vertical direction Horizontal direction m Mode The number of dots Dot density Dot density Maximum number of dots 0 8-dot single-density 8 60 DPI 80 DPI 210 1 8-dot double-density 8 60 DPI 160 DPI 420 [Notes] The number of dots in the horizontal direction depends on the printing area and the printing direction specified by ESC W and ESC T. • The nL and nH indicate the number of dots of the bit image in the horizontal direction. The number of dots is calculated by nL + nH ✕ 256. • If the bit-image data input exceeds the number of dots to be printed on a line, the excess data is ignored. • d indicates the bit-image data. Set a corresponding bit to 1 to print a dot or to 0 to not print a dot. • If the values of m and nH are out of the specified range, the following data is processed as normal data. • After printing a bit image, the printer returns to normal data processing mode. • In page mode, double density bit image data is not available. • The relationship between the image data and the dots to be printed is shown on the next page. Commands 5-11
Page 1 and 2: TM-U295/U295P Operator’s Manual U
Page 3 and 4: Printer parts (1) Upper case (2) Pr
Page 5 and 6: FCC CLASS A FCC Compliance Statemen
Page 7 and 8: DECLARATION of CONFORMITY for CE MA
Page 9 and 10: About This Manual Setting Up and Us
Page 11 and 12: Chapter 5 Commands Command Notation
Page 13 and 14: Removing the Transportation Damper
Page 15 and 16: 2. Connect the other end of the cab
Page 17 and 18: Den Drucker an die Lade anschließe
Page 19 and 20: Connecting the Power Supply This pr
Page 21 and 22: CAUTION: Be sure to perform the ste
Page 23 and 24: 8. To put the cover back on the pri
Page 25 and 26: 3. While holding down the RELEASE b
Page 27 and 28: TM-U295 Switch Function ON OFF 1 Da
Page 29 and 30: Chapter 2 Using the Printer The con
Page 31 and 32: Then remove the used ribbon by gras
Page 33 and 34: Chapter 4 Reference Information Pri
Page 35 and 36: Paper Specifications Paper type: To
Page 37 and 38: Printing position NOTE 1. Mechanica
Page 39 and 40: EMI and Safety Standards EMI standa
Page 41 and 42: Chapter 5 Commands Command Notation
Page 43 and 44: [Description] Prints the data in th
Page 45 and 46: Bit Off/On Hex Decimal Function 3 O
Page 47 and 48: [Description] Sets the character sp
Page 49: • d is the dot data for the chara
Page 53 and 54: Hex 1B 3D n Decimal 27 61 n [Range]
Page 55 and 56: [Notes] • Up to 32 tab positions
Page 57 and 58: [Default] [Reference] Double-densit
Page 59 and 60: dx = [dxL + dxH ✕ 256] dy = [dyL
Page 61 and 62: [Range] 0 ≤ n ≤ 255 [Descriptio
Page 63 and 64: [Description] Sets the time that th
Page 65 and 66: • When Auto Status Back (ASB) is
Page 67 and 68: [Description] Turns upside-down pri
Page 69 and 70: Bit Off/On Hex Decimal Status for A
Page 71 and 72: Third byte (paper sensor informatio
Page 73 and 74: • When Auto Status Back (ASB) is

TM-U295/U295P

Create successful ePaper yourself

Delete template?

Save as template?