TM-U295/U295P

More documents

Recommendations

Info

n = 5: Slip paper status Bit Off/On Hex Decimal Function 0 Off 00 0 Not used. Fixed to Off. 1 On 02 2 Not used. Fixed to Off. 2 Off 00 0 Slip paper selected. 3 Off 00 0 Does not wait for slip paper insertion. On 08 8 Waits for slip paper insertion. 4 On 10 16 Not used. Fixed to On. 5 6 Off 00 0 Slip is detected by the BOF sensor. On 20 32 Slip is not detected by the BOF sensor. Off 00 0 Slip is not detected by the TOF sensor. On 40 64 Slip is detected by the TOF sensor. 7 Off 00 0 Not used. Fixed to Off. Bit 3: Bit 5 and 6: [Reference] Becomes Off (not waiting) just before actual slip selection takes place after slip paper is detected Transmits the current status of the TOF and BOF sensors. ESC u, ESC v, GS a CAN [Name] Cancel print data in page mode [Format] ASCII CAN Hex 18 Decimal 24 [Description] In page mode, deletes all the print data in the current printable area. [Notes] • This command is enabled only in page mode. • If data that existed in the previously specified printable area also exists in the currently specified printable area, it is deleted. [Reference] ESC W ESC SP n [Name] Set right-side character spacing [Format] ASCII ESC SP n Hex 1B 20 n Decimal 27 32 n [Range] 0 ≤ n ≤ 32 5-6 Commands
[Description] Sets the character spacing for the right side of the character. [Notes] • The right-side character spacing for double-width mode is twice the normal value. • The character spacing is set in increment of half dot. • In page mode, the actual dot positions shift by half dot. • This command sets values independently in standard mode and in page mode. [Default] n = 0 ESC ! n [Name] Select print mode(s) [Format] ASCII ESC ! n Hex 1B 21 n Decimal 27 33 n [Range] 0 ≤ n ≤ 255 [Description] Selects print mode(s) using n as follows: Bit Off/On Hex Decimal Function 0 1 2 3 4 5 6 7 Off 00 0 Character font 5 ✕ 7 selected. On 01 1 Character font 7 ✕ 7 selected. Off 00 0 Undefined. On 02 2 Undefined. Off 00 0 Undefined On 04 4 Undefined. Off 00 0 Undefined. On 08 8 Undefined. Off 00 0 Double-height mode not selected. On 10 16 Double-height mode selected. Off 00 0 Double-width mode not selected. On 20 32 Double-width mode selected. Off 00 0 Undefined. On 40 64 Undefined. Off 00 0 Underline mode not selected. On 80 128 Underline mode selected. Commands 5-7
Page 1 and 2: TM-U295/U295P Operator’s Manual U
Page 3 and 4: Printer parts (1) Upper case (2) Pr
Page 5 and 6: FCC CLASS A FCC Compliance Statemen
Page 7 and 8: DECLARATION of CONFORMITY for CE MA
Page 9 and 10: About This Manual Setting Up and Us
Page 11 and 12: Chapter 5 Commands Command Notation
Page 13 and 14: Removing the Transportation Damper
Page 15 and 16: 2. Connect the other end of the cab
Page 17 and 18: Den Drucker an die Lade anschließe
Page 19 and 20: Connecting the Power Supply This pr
Page 21 and 22: CAUTION: Be sure to perform the ste
Page 23 and 24: 8. To put the cover back on the pri
Page 25 and 26: 3. While holding down the RELEASE b
Page 27 and 28: TM-U295 Switch Function ON OFF 1 Da
Page 29 and 30: Chapter 2 Using the Printer The con
Page 31 and 32: Then remove the used ribbon by gras
Page 33 and 34: Chapter 4 Reference Information Pri
Page 35 and 36: Paper Specifications Paper type: To
Page 37 and 38: Printing position NOTE 1. Mechanica
Page 39 and 40: EMI and Safety Standards EMI standa
Page 41 and 42: Chapter 5 Commands Command Notation
Page 43 and 44: [Description] Prints the data in th
Page 45: Bit Off/On Hex Decimal Function 3 O
Page 49 and 50: • d is the dot data for the chara
Page 51 and 52: ESC ✽ m nL n H [d]k [Name] Select
Page 53 and 54: Hex 1B 3D n Decimal 27 61 n [Range]
Page 55 and 56: [Notes] • Up to 32 tab positions
Page 57 and 58: [Default] [Reference] Double-densit
Page 59 and 60: dx = [dxL + dxH ✕ 256] dy = [dyL
Page 61 and 62: [Range] 0 ≤ n ≤ 255 [Descriptio
Page 63 and 64: [Description] Sets the time that th
Page 65 and 66: • When Auto Status Back (ASB) is
Page 67 and 68: [Description] Turns upside-down pri
Page 69 and 70: Bit Off/On Hex Decimal Status for A
Page 71 and 72: Third byte (paper sensor informatio
Page 73 and 74: • When Auto Status Back (ASB) is

TM-U295/U295P

Create successful ePaper yourself

Delete template?

Save as template?