ÿþþ ÿ R O - C A N - I N T E R F A C E ...

More documents

Recommendations

Info

6.1.4. Access via provided test programs We provide simple handling test programs for the most important functions of our products. These will be installed automatically by the installation of the DELIB driver library. So you can test directly e.g. relays or you can check the voltage of an A/D converter. Software |Seite 52
6.2. DELIB driver library 6.2.1. Overview The following figure explains the structure of the DELIB driver library The DELIB driver library allows an uniform response of DEDITEC hardware with particular consideration of the following viewpoints: Independent of operating system Independent of programming language Independent of the product 6.2.1.1. Program under diverse operating systems The DELIB driver library allows an uniform response of our products on diverse operating systems. We has made sure, that all of our products can be responded by a few commands. Whatever which operating system you use. - Therefore the DELIB cares! Software |Seite 53
Page 1 and 2: RO-CAN-INTERFACE Hardware-Descripti
Page 3 and 4: INDEX 5.1.1.1. Select Config-Port (
Page 5 and 6: INDEX 6.4. Test programs 85 6.4.1.
Page 7 and 8: 1. Introduction 1.1. General remark
Page 9 and 10: 2. Hardware description 2.1. Overvi
Page 11 and 12: 2.3. Plug-in connector of the modul
Page 13 and 14: Configuring the module III Configur
Page 15 and 16: 3.2. The “special mode” The ”
Page 17 and 18: Approach: 1. Choose the RO-CAN modu
Page 19 and 20: 3.4.2. Setting up the CAN module ad
Page 21 and 22: Firmware update IV Firmware update
Page 23 and 24: 1. Select the Interface of the modu
Page 25 and 26: CAN-Configuration Utility V CAN-Con
Page 27 and 28: 5.1. Configuration 5.1.1. Basic con
Page 29 and 30: 5.1.2. Select the configuration 5.1
Page 31 and 32: 5.1.3.3. Set the D/A value range (3
Page 33 and 34: 5.1.4.3. Set the response module ad
Page 35 and 36: 5.1.6. Auto Rx mode The automatic r
Page 37 and 38: 5.2. Structure of the CAN packets 5
Page 39 and 40: 5.2.3. Digital input counter (16-bi
Page 41 and 42: 5.2.5. A/D inputs 5.2.5.1. Structur
Page 43 and 44: 5.2.6. D/A outputs 5.2.6.1. Structu
Page 45 and 46: 5.2.7. Temperature inputs 5.2.7.1.
Page 47 and 48: 5.2.8.3. Values for par 1 for comma
Page 49 and 50: 5.3. Control LEDs The following exa
Page 51: 6. Software 6.1. Using our products
Page 55 and 56: 6.2.2. Supported operating systems
Page 57 and 58: Click on „Install“. Software |S
Page 59 and 60: The DELIB driver library is now ins
Page 61 and 62: 6.3. Integration of the DELIB 6.3.1
Page 63 and 64: DELIB.LIB entry in the Visual-C/C++
Page 65 and 66: 6.3.3. Integration of the delib.cs
Page 67 and 68: The Configuration Manager Open the
Page 69 and 70: 6.3.4. Integration of the delib.pas
Page 71 and 72: 6.3.6. Integration of the delib.vb
Page 73 and 74: Creation of UserForm Create a new U
Page 75 and 76: - Choose the option "create VIs for
Page 77 and 78: - Press continue again - The Header
Page 79 and 80: - In the new window choose "Easy er
Page 81 and 82: - In addition for some VIs you need
Page 83 and 84: 6.3.8.2. Usage of the VIs in LabVIE
Page 85 and 86: 6.4. Test programs 6.4.1. Digital I
Page 87 and 88: 6.4.3. Stepper Demo Start “Steppe
Page 89 and 90: 6.4.5. Temperature Read Demo Start
Page 91 and 92: Return-value Read state of the inpu
Page 93 and 94: 6.5.2. Customisation for RO-ETH-Mod
Page 95 and 96: Digitale Inputs Windows delib_cli D
Page 97 and 98: Analog Inputs Windows delib_cli AI
Page 99 and 100: 7. Appendix 7.1. Revisions Rev 1.00

ÿþþ ÿ R O - C A N - I N T E R F A C E ...

Create successful ePaper yourself

Delete template?

Save as template?