ÿþþ ÿ R O - C A N - I N T E R F A C E ...

More documents

Recommendations

Info

- VIs which are working with 64-bit values must be edited. The display must be changed from "unsigned long" to "unsigned quad". - The following VIs must be edited: -> DapiCNT48CounterGet48 (function return) -> DapiDIGet64 (function return) -> DapiDOSet64 (data) -> DapiDOReadBack64 (function return) Software |Seite 80
- In addition for some VIs you need to change the elementype to "numeric". - The following VIs must be edited: -> DapiWriteLongLong (value) -> DapiReadLongLong (function return) - Afterwards press continue. Software |Seite 81
Page 1 and 2:
RO-CAN-INTERFACE Hardware-Descripti
Page 3 and 4:
INDEX 5.1.1.1. Select Config-Port (
Page 5 and 6:
INDEX 6.4. Test programs 85 6.4.1.
Page 7 and 8:
1. Introduction 1.1. General remark
Page 9 and 10:
2. Hardware description 2.1. Overvi
Page 11 and 12:
2.3. Plug-in connector of the modul
Page 13 and 14:
Configuring the module III Configur
Page 15 and 16:
3.2. The “special mode” The ”
Page 17 and 18:
Approach: 1. Choose the RO-CAN modu
Page 19 and 20:
3.4.2. Setting up the CAN module ad
Page 21 and 22:
Firmware update IV Firmware update
Page 23 and 24:
1. Select the Interface of the modu
Page 25 and 26:
CAN-Configuration Utility V CAN-Con
Page 27 and 28:
5.1. Configuration 5.1.1. Basic con
Page 29 and 30: 5.1.2. Select the configuration 5.1
Page 31 and 32: 5.1.3.3. Set the D/A value range (3
Page 33 and 34: 5.1.4.3. Set the response module ad
Page 35 and 36: 5.1.6. Auto Rx mode The automatic r
Page 37 and 38: 5.2. Structure of the CAN packets 5
Page 39 and 40: 5.2.3. Digital input counter (16-bi
Page 41 and 42: 5.2.5. A/D inputs 5.2.5.1. Structur
Page 43 and 44: 5.2.6. D/A outputs 5.2.6.1. Structu
Page 45 and 46: 5.2.7. Temperature inputs 5.2.7.1.
Page 47 and 48: 5.2.8.3. Values for par 1 for comma
Page 49 and 50: 5.3. Control LEDs The following exa
Page 51 and 52: 6. Software 6.1. Using our products
Page 53 and 54: 6.2. DELIB driver library 6.2.1. Ov
Page 55 and 56: 6.2.2. Supported operating systems
Page 57 and 58: Click on „Install“. Software |S
Page 59 and 60: The DELIB driver library is now ins
Page 61 and 62: 6.3. Integration of the DELIB 6.3.1
Page 63 and 64: DELIB.LIB entry in the Visual-C/C++
Page 65 and 66: 6.3.3. Integration of the delib.cs
Page 67 and 68: The Configuration Manager Open the
Page 69 and 70: 6.3.4. Integration of the delib.pas
Page 71 and 72: 6.3.6. Integration of the delib.vb
Page 73 and 74: Creation of UserForm Create a new U
Page 75 and 76: - Choose the option "create VIs for
Page 77 and 78: - Press continue again - The Header
Page 79: - In the new window choose "Easy er
Page 83 and 84: 6.3.8.2. Usage of the VIs in LabVIE
Page 85 and 86: 6.4. Test programs 6.4.1. Digital I
Page 87 and 88: 6.4.3. Stepper Demo Start “Steppe
Page 89 and 90: 6.4.5. Temperature Read Demo Start
Page 91 and 92: Return-value Read state of the inpu
Page 93 and 94: 6.5.2. Customisation for RO-ETH-Mod
Page 95 and 96: Digitale Inputs Windows delib_cli D
Page 97 and 98: Analog Inputs Windows delib_cli AI
Page 99 and 100: 7. Appendix 7.1. Revisions Rev 1.00
show all

ÿþþ ÿ R O - C A N - I N T E R F A C E ...

Create successful ePaper yourself

Delete template?

Save as template?