ZIRCONIA OXYGEN PROBE OUTPUT (mV) - Novatech Controls

More documents

Recommendations

Info

INSTALLATION & COMMISSIONING SECTION NUMBER INSTALLATION 3 3.1 MOUNTING THE ANALYSER 3.2 HEATER INTERLOCK RELAYS 3.3 EARTH, SHIELD & POWER CONNECTIONS 3.4 CONNECTING THE PROBE CABLE 3.5 CONNECTING THE FLUE THERMOCOUPLE (OPTIONAL) 3.6 CONNECTING THE RELATIVE HUMIDITY SENSOR (OPTIONAL) 3.7 CONNECTING THE AMBIENT TEMPERATURE SENSOR (OPTIONAL) 3.8 CONNECTING THE OUTPUT CHANNELS 3.9 CONNECTING THE ALARMS 3.10 CONNECTING THE HORN RELAY 3.11 CONNECTING THE AUTOMATIC PURGE & CALIBRATION SYSTEM 3.12 CONNECTING REFERENCE AIR 3.13 CONNECTING THE DUAL FUEL INPUT 3.14 CONNECTING THE PRINTER 3.15 INSTALLING THE OXYGEN PROBE 3.16 INSTALLING THE FLUE THERMOCOUPLE COMMISSIONING 3.17 CONNECTING POWER –COLD START 3.18 REFERENCE AIR FLOW SWITCH 3.19 COMMISSIONING – MAINTENANCE MODE 3.20 COMMISSIONING – SET-UP MODE 3.21 RUN MODE 3.22 HEATER BY-PASS SWITCH 3.23 CHECKING THE ALARMS 3.24 PROBE CALIBRATION 3.25 FILTER PURGE SET-UP PROCEDURE 3.26 CALIBRATION GAS SET-UP PROCEDURE 3.27 DUST IN THE FLUE GAS 3.28 STRATIFICATION
3.1 MOUNTING THE ANALYSER 355 INSTALLATION Surface mount the transmitter case on to a flat surface or bracket, using the four holes provided. Refer to Figure 3.1. If the hole layout provided is not suitable then the circuit boards may be removed and additional holes drilled in the rear of the case. Mounting screws should not come into contact with the printed circuit boards. All wiring should comply with local electrical codes. The lead between the probe and transmitter should be ordered with the probe. It has an integral weatherproof connector to plug into the probe head. FRONT REAR SIDE 319 All Dimensions in Millimetres 12.5 3.2 HEATER INTERLOCK RELAYS 30 30 9.5 Holes 294 NOVATECH OXYGEN ANALYZER 3.1 12.5 Figure 3.1 Case Mounting Dimensions CAUTION Explosion protection for heated probes is achieved by switching the power to the probe heater off whenever the main fuel valve is closed. The principle of safety is that if the main fuel valve is open then main flame has been established. With this primary source of ignition on, the probe heater can be safely switched on. The most dangerous situation is if fuel leaks into the combustion appliance when the fuel valve is closed. When power is removed from the main fuel valve the heater should also be switched off. To achieve this protection, connect the main fuel valve power to the ‘BURNER ON I/P’ terminals and check that relay RL7 coil is compatible with the voltage connected e.g. 110 or 240 VAC.For Installation where there is no risk of explosion, connect a constant mains supply to terminals number 39 & 40. Refer to Figure 3.2. 38 155 132
Page 1 and 2: CONTENTS 1. SPECIFICATIONS 2. DESCR
Page 3 and 4: SPECIFICATIONS 1.1 MODEL 1532 OXYGE
Page 5 and 6: Range of Output 2 Field selectable
Page 7 and 8: Series 1230 probes are simple to in
Page 9 and 10: SPECIFICATIONS MODEL 1231 1232 1233
Page 11 and 12: 1.3 FLOW GUIDE TUBES The maximum in
Page 13: 1.6 SPECIFICATIONS - REFERENCE AIR
Page 17 and 18: 2.1 THE ZIRCONIA SENSOR DESCRIPTION
Page 19 and 20: 2.6 APPLICATIONS WHERE SENSING POIN
Page 21: Figure 2.2 1532 Analyser Block Diag
Page 25 and 26: Zirconi Senso Zirconia Sensor Prob
Page 27 and 28: Figure 3.6 Connections for Relative
Page 29 and 30: Figure 3.9 Connections for Alarm Ho
Page 31 and 32: Figure 3.11 Reference Air Connectio
Page 33 and 34: Figure 3.14 Mounting of Flow Guide
Page 35 and 36: 3.22 HEATER BY-PASS SWITCH Heated p
Page 37: NOVATECH OXYGEN ANALYZER 3.15
Page 41 and 42: 4.1 DISPLAY BUTTON NOTE: OPERATOR F
Page 43 and 44: ALARM DESCRIPTION ‘FILTER BLOCKED
Page 45: SETTING UP THE ANALYSER SECTION NUM
Page 48 and 49: 5.2 SET-UP/MAINTENANCE/RUN SWITCH F
Page 50 and 51: 5. TRANSMITTER SPAN CHANNEL 1 Appli
Page 52 and 53: 13. SINGLE OR DUAL FUEL Enter singl
Page 54 and 55: 33. NUMBER OF CAL GASES Select the
Page 56 and 57: 49. RELATIVE HUMIDITY SENSOR CONNEC
Page 59 and 60: 6.1 MAINTENANCE MODE SUMMARY 1. ENT
Page 61 and 62: 19 20 CN2 VOLTAGE REFERENCE TEST PO
Page 63 and 64: 11. SET CALIBRATION FACTOR FOR 4-20
Page 65 and 66: If the probe tests reveal less than
Page 67 and 68: APPENDICES 1. CONSTITUENT VALUES FO
Page 69 and 70: FUEL A H O N S M __________________
Page 71 and 72: ZIRCONIA OXYGEN PROBE OUTPUT (mV) P
Page 73 and 74:
ZIRCONIA OXYGEN PROBE OUTPUT (mV),
Page 75 and 76:
12.07: 12/02/93 APPENDIX 4 SAMPLE L
show all

ZIRCONIA OXYGEN PROBE OUTPUT (mV) - Novatech Controls

Create successful ePaper yourself

Delete template?

Save as template?