ZIRCONIA OXYGEN PROBE OUTPUT (mV) - Novatech Controls

More documents

Recommendations

Info

Figure 3.2 Heater Supply Interlock Connection For Heated Probes 3.3 EARTH, SHIELD & POWER CONNECTIONS All external earthing should be shielded. The printed circuit boards are fully floating above earth. All earth and shield connections should be connected to the earth terminal number 44. The mains earth should be connected to a sound electrical earth.Do not connect shields at the field end. Simply clip off and insulate. An extra terminal strip may be required to connect all shields together. This should be supplied by the installer. Before connection of mains power check that the correct solder links are installed as shown in Figure 3.3. Figure 3.3 Earth, Shield and Power Connections 3.2 NOVATECH <strong>OXYGEN</strong> ANALYSER
Zirconi Senso Zirconia Sensor Prob Thermocou Prob Heate Prob Eart Probe Head Connector Probe Thermocouple (Optional) E A B E C Note 1: Jumper terminals 3 & 4 to terminals 5 & 6 if efficiency or flue temperature display is required. Use copper wire. F D Other Shields Mains Earth Green & Yellow (Shield) Orange Figure 3.4a Connection of Probe Cable for Unheated Probes Models 1232 and 1233. Probe Connect C B A F D E G Gree G C A B Othe Shield Main Eart Plug mounted on head viewed from outside of head. Green Yello (Shiel Reducing Fitting Ref Air Figure 3.4b Connection of Probe Cable for Heated Probes Model 1231. NOVATECH <strong>OXYGEN</strong> ANALYZER 3.3 Black *Note 1 Red Shield Common Terminal Block Orange Brown Black Blue Whit Whit Shiel Commo Terminal 1/4" PVC tube to reference air supply. 1 Probe + 2 Probe - 3 Probe TC + 4 Probe TC - 44 Earth 1 Probe 2 Probe 3 Probe TC 4 Probe TC 37 38 44
Page 1 and 2: CONTENTS 1. SPECIFICATIONS 2. DESCR
Page 3 and 4: SPECIFICATIONS 1.1 MODEL 1532 OXYGE
Page 5 and 6: Range of Output 2 Field selectable
Page 7 and 8: Series 1230 probes are simple to in
Page 9 and 10: SPECIFICATIONS MODEL 1231 1232 1233
Page 11 and 12: 1.3 FLOW GUIDE TUBES The maximum in
Page 13: 1.6 SPECIFICATIONS - REFERENCE AIR
Page 17 and 18: 2.1 THE ZIRCONIA SENSOR DESCRIPTION
Page 19 and 20: 2.6 APPLICATIONS WHERE SENSING POIN
Page 21 and 22: Figure 2.2 1532 Analyser Block Diag
Page 23: 3.1 MOUNTING THE ANALYSER 355 INSTA
Page 27 and 28: Figure 3.6 Connections for Relative
Page 29 and 30: Figure 3.9 Connections for Alarm Ho
Page 31 and 32: Figure 3.11 Reference Air Connectio
Page 33 and 34: Figure 3.14 Mounting of Flow Guide
Page 35 and 36: 3.22 HEATER BY-PASS SWITCH Heated p
Page 37: NOVATECH OXYGEN ANALYZER 3.15
Page 41 and 42: 4.1 DISPLAY BUTTON NOTE: OPERATOR F
Page 43 and 44: ALARM DESCRIPTION ‘FILTER BLOCKED
Page 45: SETTING UP THE ANALYSER SECTION NUM
Page 48 and 49: 5.2 SET-UP/MAINTENANCE/RUN SWITCH F
Page 50 and 51: 5. TRANSMITTER SPAN CHANNEL 1 Appli
Page 52 and 53: 13. SINGLE OR DUAL FUEL Enter singl
Page 54 and 55: 33. NUMBER OF CAL GASES Select the
Page 56 and 57: 49. RELATIVE HUMIDITY SENSOR CONNEC
Page 59 and 60: 6.1 MAINTENANCE MODE SUMMARY 1. ENT
Page 61 and 62: 19 20 CN2 VOLTAGE REFERENCE TEST PO
Page 63 and 64: 11. SET CALIBRATION FACTOR FOR 4-20
Page 65 and 66: If the probe tests reveal less than
Page 67 and 68: APPENDICES 1. CONSTITUENT VALUES FO
Page 69 and 70: FUEL A H O N S M __________________
Page 71 and 72: ZIRCONIA OXYGEN PROBE OUTPUT (mV) P
Page 73 and 74: ZIRCONIA OXYGEN PROBE OUTPUT (mV),
Page 75 and 76:
12.07: 12/02/93 APPENDIX 4 SAMPLE L
show all

ZIRCONIA OXYGEN PROBE OUTPUT (mV) - Novatech Controls

Create successful ePaper yourself

Delete template?

Save as template?