2018 Ascot Buyer's Guide_compressed

260
VALVE HARDWARE // VALVES & VALVE TOOLS
Single, Double and Triple Bend Swivel Valves
Z-Bore Valve System
There are three spud types available: the standard clamp-in spud, a screw-in spud and an angle screw-in spud.
There is no temporary outside-in clamp-in spud for Z-Bore. The Z-Bore Valve System is very similar to the Super
Large Bore System. By using an O-Ring to seal the clamp-in spud to the rim, a greater flow diameter is created
without sacrificing strength or performance. Flows 370 CFM compared to 240 CFM on the Z-Bore Valve System.
Z-1 SCREW-IN SPUD
Z-2 CLAMP-IN SPUD
VALVE HARDWARE // VALVES & VALVE TOOLS
• The screw-in spud is used to
attach any Z-Bore valves to the rim
• Designed to screw into a 1/2" NPTtapped
rim hole • Can be changed
without demounting the tire
ASCOT NO. MFG. NO. DESCRIPTION
466-70001 Z-1 Screw-In Spud
Z-13 SCREW-IN SPUD
• The Z-13 screw-In spud screws into
the 3/4" NPT-tapped rim hole and
converts Mega Bore to Z-Bore
ASCOT NO. MFG. NO. DESCRIPTION
466-70013 Z-13 Screw-In Spud
ANGLE CONNECTOR
• Connectors of various angles
and lengths are available • The
connector accommodates a
flexible extension which attaches
to the Z-10 core housing
ASCOT NO. MFG. NO. DESCRIPTION
469-70360 Z3-60 60° Angle
466-70375 Z3-75 75˚ Angle
466-70380 Z3-80 80˚ Angle
466-70390 Z3-90 90˚ Angle
466-70001
466-70013
466-70390
• Can attach any Z-Bore valve to the rim
through a standard valve hole (13/16")
• Fits a 13/16" diameter valve hole • Tire
must be dismounted to change spud
ASCOT NO. MFG. NO. DESCRIPTION
466-70002 Z-2 Clamp-In Spud
Z-4 ANGLE SCREW-IN SPUD
• Fits 1/2" NPT-tapped rim
hole • 85˚ bend angle
ASCOT NO. MFG. NO. DESCRIPTION
466-70004 Z-4 Angle Screw-In Spud
Z-BORE FLEXIBLE EXTENSIONS
466-70002
466-70004
• Made up in any length to allow extension to fit the wheel
configuration • Specially designed fittings and thermoplastic
hose will not fatigue or crush during service • Corrosion
problems are eliminated • Able to customize extension in the
field • ZFAK field assembly kit available to assemble your own
ASCOT NO. MFG. NO. DESCRIPTION
466-70700 ZBFE- Flexible Extension
Length
466-70701 ZFAK Assembly Kit For Z-Bore
Valves. INCLUDES:
Contains Z-8 Swivel
Connector, Z-7 Straight
Tubing Connector,
2x Z2-2 Nuts, 2x Z-9
Tubing Connector
Sleeves, Z-10 Core
Housing. Z-100 Tubing
Is Ordered Separately
Z-10 CORE HOUSING
• Complete with core and cap • Integral
part of the system as the Z-10 is
removed from the valve assembly with
the Haltec Z-12B inflator to utilize the
larger opening and the fullest flow
ASCOT NO. MFG. NO. DESCRIPTION
466-70010 Z-10 Core Housing
w/Core & Cap
466-70010
Z-12B INFLATOR
• To maximize air flow, a Z-12B inflator
is used to remove core housing during
inflation and deflation • Operates like
the IN-80A Super Large Bore inflator
ASCOT NO. MFG. NO. DESCRIPTION
466-70012 Z-12B Inflator 466-70012
BUYER'S GUIDE
ASCOT SUPPLY CORPORATION
SUPPLY CORPORATION