Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
ABB i-bus ® KNX<br />
Product Article-No. Order-No. Pack/Qty<br />
Light controller, 4-gang, 1-10V, MDRC<br />
In conjunction with electronic ballast units, enables the<br />
switching and dimming of light current circuits via 2 or 4<br />
independent channels. In conjunction with the LF/U 2.1<br />
light sensor, constant light regulation can be realised. For<br />
a precise detection of the lighting conditions, up to 2 or 4<br />
light sensor can be connected to a controller.<br />
Control element: Manual operation possibility for ON/OFF<br />
via sliding switch<br />
Display elements: Status display of the outputs via position<br />
of the sliding switches<br />
Connections:<br />
KNX-line: Bus terminal<br />
Rated voltage: 230 V<br />
Secondary: 440 V<br />
Rated frequency: 50 Hz/60 Hz<br />
Outputs: 4x Normally open contact, potential free<br />
Suitable for: AC1<br />
Rated current: 16 A, cos 1<br />
Output voltage: 230 V~<br />
Suitable for: AC3<br />
Rated current: 10 AX<br />
Output voltage: 230 V~<br />
Control/Signal outputs: 4, electronic output, 0-10 V<br />
Rated current: 100 mA<br />
max. length: 100 m<br />
Protection class (Device): IP 20<br />
Temperature range (Device): -5 °C to 45 °C<br />
Dimensions: (L x W x D): 90 mm x 144 mm x 64 mm<br />
Installation depth: 68 mm<br />
module width: 8 MW<br />
LR/S 4.16.1 2CDG110088R0011<br />
Light sensor, FM<br />
Used in conjunction with the LR/S x.16.1 light controllers<br />
for constant light regulation. Various light control rods, the<br />
connecting terminal, and the cover for discrete installation<br />
in the room are included in delivery.<br />
Protection class (Device): IP 20<br />
Temperature range (Device): -5 °C to 45 °C<br />
Dimensions: (L x W x D): 20 mm x 54 mm<br />
LF/U 2.1 2CDG110089R0011<br />
Switch/dimm actuator 1 ) 2 )<br />
2gang<br />
MDRC devices for switching and dimming independent<br />
lamp groups from electrical ballast units with a 1-10V<br />
control interface via ABB i-bus ® . For each channel the<br />
supply voltage of the ballast units can be switched on or<br />
off manually with a fl oating load relay (16A-AC1) via ABB<br />
i-bus ® . A switching state display is present. No power<br />
supply is required.<br />
Control element: Manual operation possibility for ON/OFF<br />
via sliding switch<br />
Display elements: Status display of the outputs via position<br />
of the sliding switches<br />
Connections:<br />
KNX-line: Bus terminal<br />
Rated voltage: 230 V~, +10 % / -15 %<br />
Rated frequency: 50 Hz/60 Hz<br />
Outputs: 2x Normally open contact, potential free<br />
Suitable for: AC1<br />
Rated current: 10 A, cos 1<br />
Output voltage: 230 V~<br />
Suitable for: AC3<br />
Rated current: 8 A, cos 0.65<br />
Output voltage: 230 V~<br />
Control/Signal outputs: 2, electronic output, 0-10 V<br />
Rated current: 100 mA<br />
Protection class (Device): IP 20<br />
Temperature range (Device): -5 °C to 45 °C<br />
Dimensions: (L x W x D): 90 mm x 72 mm x 64 mm<br />
Installation depth: 68 mm<br />
module width: 4 MW<br />
SD/S 2.16.1 2CDG110079R0011<br />
1) As required, you can fi nd the programmable functions in the current application description, which<br />
you can download in the Support Centre on our Internet page.<br />
2) 1 MW 18 mm.<br />
Technical information<br />
www.BUSCH-JAEGER-catalogue.com<br />
Product Article-No. Order-No. Pack/Qty<br />
Switch/dimm actuator 1 ) 2 )<br />
4gang<br />
MDRC devices for switching and dimming independent<br />
lamp groups from electrical ballast units with a 1-10V<br />
control interface via ABB i-bus ® . For each channel the<br />
supply voltage of the ballast units can be switched on or<br />
off manually with a fl oating load relay (16A-AC1) via ABB<br />
i-bus ® . A switching state display is present. No power<br />
supply is required.<br />
Control element: Manual operation possibility for ON/OFF<br />
via sliding switch<br />
Display elements: Status display of the outputs via position<br />
of the sliding switches<br />
Connections:<br />
KNX-line: Bus terminal<br />
Rated voltage: 230 V~, +10 % / -15 %<br />
Rated frequency: 50 Hz/60 Hz<br />
Outputs: 4x Normally open contact, potential free<br />
Suitable for: AC1<br />
Rated current: 10 A, cos 1<br />
Output voltage: 230 V~<br />
Suitable for: AC3<br />
Rated current: 8 A, cos 0.65<br />
Output voltage: 230 V~<br />
Control/Signal outputs: 4, electronic output, 0-10 V<br />
Rated current: 100 mA<br />
Protection class (Device): IP 20<br />
Temperature range (Device): -5 °C to 45 °C<br />
Dimensions: (L x W x D): 90 mm x 108 mm x 64 mm<br />
Installation depth: 68 mm<br />
module width: 6 MW<br />
SD/S 4.16.1 2CDG110080R0011<br />
1) As required, you can fi nd the programmable functions in the current application description, which<br />
you can download in the Support Centre on our Internet page.<br />
2) 1 MW 18 mm.<br />
Switch/dimm actuator 1 ) 2 )<br />
8gang<br />
MDRC devices for switching and dimming independent<br />
lamp groups from electrical ballast units with a 1-10V<br />
control interface via ABB i-bus ® . For each channel the<br />
supply voltage of the ballast units can be switched on or<br />
off manually with a fl oating load relay (16A-AC1) via ABB<br />
i-bus ® . A switching state display is present. No power<br />
supply is required.<br />
Control element: Manual operation possibility for ON/OFF<br />
via sliding switch<br />
Display elements: Status display of the outputs via position<br />
of the sliding switches<br />
Connections:<br />
KNX-line: Bus terminal<br />
Rated voltage: 230 V~, +10 % / -15 %<br />
Rated frequency: 50 Hz/60 Hz<br />
Outputs: 8x Normally open contact, potential free<br />
Suitable for: AC1<br />
Rated current: 10 A, cos 1<br />
Output voltage: 230 V~<br />
Suitable for: AC3<br />
Rated current: 8 A, cos 0.65<br />
Output voltage: 230 V~<br />
Control/Signal outputs: 8, electronic output, 0-10 V<br />
Rated current: 100 mA<br />
Protection class (Device): IP 20<br />
Temperature range (Device): -5 °C to 45 °C<br />
Dimensions: (L x W x D): 90 mm x 144 mm x 64 mm<br />
Installation depth: 68 mm<br />
SD/S 8.16.1 2CDG110081R0011<br />
1) As required, you can fi nd the programmable functions in the current application description, which<br />
you can download in the Support Centre on our Internet page.<br />
2) 1 MW 18 mm.<br />
449