clevo m860tu.pdf - tim.id.au

More documents

Recommendations

Info

1.Introduction Introduction 1-14
2: Disassembly Overview This chapter provides step-by-step instructions for disassembling the M860TU series notebook’s parts and subsystems. When it comes to reassembly, reverse the procedures (unless otherwise indicated). We suggest you completely review any procedure before you take the computer apart. Procedures such as upgrading/replacing the RAM, CD device and hard disk are included in the User’s Manual but are repeated here for your convenience. To make the disassembly process easier each section may have a box in the page margin. Information contained under the figure # will give a synopsis of the sequence of procedures involved in the disassembly procedure. A box with a � lists the relevant parts you will have after the disassembly process is complete. Note: The parts listed will be for the disassembly procedure listed ONLY, and not any previous disassembly step(s) required. Refer to the part list for the previous disassembly procedure. The amount of screws you should be left with will be listed here also. A box with a � will also provide any possible helpful information. A box with a � contains warnings. An example of these types of boxes are shown in the sidebar. Disassembly � Information � Warning Overview 2 - 1 2.Disassembly
Page 3 and 4: Notebook Computer M860TU Service Ma
Page 5 and 6: About this Manual This manual is in
Page 7 and 8: Instructions for Care and Operation
Page 9 and 10: Battery Precautions • Only use ba
Page 11 and 12: Introduction ......................
Page 13 and 14: 1: Introduction Overview This manua
Page 15 and 16: Feature Specification Video Adapter
Page 17 and 18: Feature Specification Power Full Ra
Page 19 and 20: External Locator - Front and Rear V
Page 21 and 22: External Locator - Bottom View 1 1
Page 23 and 24: Introduction Mainboard Overview - B
Page 25: Introduction Mainboard Overview - B
Page 29 and 30: Maintenance Precautions The followi
Page 31 and 32: Removing the Battery 1. Turn the co
Page 33 and 34: 6. Remove screws 11 - 12 from the h
Page 35 and 36: Removing the System Memory (RAM) Th
Page 37 and 38: 5. Turn the release latch 11 toward
Page 39 and 40: Removing the VGA Card 1. Turn off t
Page 41 and 42: Removing the Wireless LAN Module 1.
Page 43 and 44: Removing the Inverter Board 1. Turn
Page 45 and 46: Removing the Modem 1. Turn off the
Page 47 and 48: Appendix A:Part Lists This appendix
Page 49 and 50: Top without Fingerprint 切除按
Page 51 and 52: Bottom 無鉛無鉛無鉛無鉛
Page 53 and 54: DVD-ROM Drive 無鉛無鉛無鉛
Page 55 and 56: HDD 無鉛 (無鉛) Figure A - 6 HD
Page 57 and 58: Appendix B:Schematic Diagrams This
Page 59 and 60: Penryn 1/2 1.05V S 4 4 H_ADSTB#0 4
Page 61 and 62: Cantiga 1/6, Host 1.05V S Layout No
Page 63 and 64: Cantiga 3/6, DDR 10 M_A_DQ[63: 0] M
Page 65 and 66: Schematic Diagrams Cantiga 5/6, GND
Page 67 and 68: DDR3 SO-DIMM 1 SO-DIMM 0 Layout Not
Page 69 and 70: LCD PANEL PVT 37 EX_ENAVD D PVT: De
Page 71 and 72: ICH9-M 2/4, PCI, USB SPI _S I i TPM
Page 73 and 74: ICH9-M 4/4, Power R T CVC C 20mils
Page 75 and 76: Clock Generator CLOCK GENERATOR 2 L
Page 77 and 78:
Card Reader & 1394 JMB380 IEEE1394
Page 79 and 80:
KBC-ITE IT8512 PVT VDD 3 C1 4 0.01u
Page 81 and 82:
LED, Screw Hole 22 LED _ACIN # R 63
Page 83 and 84:
Audio AMP 25 15 25 L_ H P _ O U T _
Page 85 and 86:
DVI, INV 37 EX_DAC _R 37 EX_DAC _G
Page 87 and 88:
Power GPU 5 DFGT_VID_4 5 DFGT_VID_3
Page 89 and 90:
Power 3.3VM/1.8VS/1.05VM P C 18 3 0
Page 91 and 92:
Power VDD3/VDD5/3.3V/5V EN_15V 22,3
Page 93 and 94:
Mini Card/WLAN MINI-PCIE CARD 15,19
Page 95 and 96:
Board to Board CON/TPM HOT KEY (M/B
Page 97 and 98:
Click Board TG ND GCO N1 TC9 33P_50
Page 99 and 100:
SIM Card Board MUIM_PWR MGND 2 MC5
show all

clevo m860tu.pdf - tim.id.au

Create successful ePaper yourself

Delete template?

Save as template?