course contents - ug - National Institute of Technology Karnataka

NATIONAL INSTITUTE OF TECHNOLOGY KARNATAKA, SURATHAKAL
------------------------------------------------------------------------------------------------------------------
Landis, Lab experiment and demonstration in fluid mechanics and heat transfer.
Sotoukhim and afgan, Measurement techniques in heat and mass transfer-Hemisphere.
Eckert and Goldstein, Measurements in heat transfer – Mc Graw Hill.
Beckwith and Buck, Mechanical Measurements – Addison Wesley.
Doeblin, Measurement Systems Application and Design – Mc Graw Hill.
ME311 FUELS & COMBUSTION (3-0-0) 3
Fuels for SI and CI engines, solid, liquid and gaseous fuels, Octane and Cetane rating method.
Combustion equipments, combustion stoichiometry. Combustion phenomenon in the SI engines,
combustion knock. factors affecting the combustion knock. Control of knock. Combustion chamber
designs for SI engine. Combustion phenomenon in the CI engines. Delay period and Diesel knock.
Factors affecting delay period. Combustion chamber designs for CI engines. Use of alternate fuels.
E.F. Obert, Internal Combustion Engine, International Textbooks & Co.
Jhon B. Heywood, Internal Combustion Engine fundamentals, McGraw Hill.
P.M. Heldt., High Speed Combustion Engines, Oxford & IBH.
Chandra Mohan and S.P. Sharma, Fuels and Combustion, Tata McGraw Hill.
ME312 MECHANICS OF METAL CUTTING AND PRESS WORKING (3-0-0) 3
Orthogonal and Oblique cutting, Tool geometry and Machining parameters, Mechanics, Force and
Temperature measurements, Surface Integrity, Tool Wear, and tool life, Machinability, Types of presses,
Dies and punches, Force calculations, Design principles. Economics of machining.
G. Boothryod, Fundamentals of Metal cutting and Machining.
B. L. Juneja and Shekon G. S., Fundamentals of Metal cutting and Machine Tools.
P. N. Rao, Manufacturing Technology.
ASME Metals Hand Book.
Taylor, Metal cutting
ME313 HYDRUALIC AND PNEUMATIC CONTROL (3-0-0) 3
Introduction, Circuit Symbols, Fluid Pumps and Motors, Control Valves, Servo Systems, Design
consideration of Circuits, Pneumatic Compressors and their Working Principles, Hydro-Pneumatics,
Fluidics, Principles of Pneumatic circuit design, Maintenance of Circuits, K-V Diagrams and Electrical
Controls in Pneumatic Circuits. PLC control of hydraulics and pneumatic systems.
Esposito A.P., Fluid Power, Pearson Education Asia
Text Book of Hydraulics and Pneumatics, Festo Didactic
Andrew Parr, Hydraulics and Pneumatics, Jaico Pub.
S.R. Majunder, Pneumatic Systems – Principles and Maintenance, Tata McGraw Hill Co.
ME314 SYNTHESIS OF MECHANISMS (3-0-0) 3
Introduction, tasks of Kinematics Synthesis, Type synthesis, Tools of dimensional synthesis, Graphical
synthesis: Motion generation-two and three prescribed motions, Path generation � three prescribed
positions, prescribed timings, four positions without prescribed timings. Function Generator: Three
prescribed points, Introduction to Analytical synthesis, Standard Dyad form, three prescribed positions for
motion, path and function generation, circle, point and center-point circles, Freudenstein�s equations for
three point function generation, order synthesis, coupler curves for four-link, slider-crank and inverted
slider-crank mechanisms, Application of coupler curves in design of six-link mechanism, Coupler cognate
mechanisms.
Arthur G. Erdman, George N, Sandor, Mechanism Design –Analysis and Synthesis, Vol. I, Prentice Hall,
New Jersey, 1984.
A.H Soni, Mechanism Synthesis and Analysis, McGraw Hill, 1984
Robert L. Norton, Design of Machinery- An Introduction to the Synthesis and Analysis of Mechanisms,
WCB Mc Graw Hill, Boston, 1999.
---------------------------------------------------------------------
NITK-Course Contents(UG)2010 Page 94 of 134