course contents - ug - National Institute of Technology Karnataka

NATIONAL INSTITUTE OF TECHNOLOGY KARNATAKA, SURATHAKAL
------------------------------------------------------------------------------------------------------------------
Dean C. Karnopp, Donald L Margolis, Ronald C. Rosenbergsystem Dynamics, Modeling and Simulation
of Mechatronics Systems, Wiley-Interscience; 3 edition 1999
ME 326 ENVIRONMENTAL POLLUTION CONTROL (3-0-0) 3
Sources and classifications of Air pollutants, Air pollution, Air Quality, characteristics and their ill
effects, Meteorology and economic effects of Air pollution, Management of Air quality, Air pollution
sampling procedures and measurements, Methods of control and equipments used. Air pollution due to
automobiles, smoke and its control, control of gaseous contaminants. Sources and classification of water
pollutants, waste water sampling and analysis, waste water treatment. Solid waste management, Noise
and odor pollution.
C.S Rao, Environmental pollution control Engineering Wiley Eastern Ltd, 1994.
Howard.S Peavy, Donald R Rowe & George Tchobanoglous, Environmental engineering, McGraw Hill
intnl. edition1986.
S.P Mahajan, Pollution control in process industries Tata McGraw Hill 1985
W.L Faith, Air pollution control, John Wiley.
Henry. C. Perkins, Air Pollution, McGraw Hill.
KVSG Murali Krishna, Air Pollution and Control, Kaushal & Co 1995.
ME 327 FLUID POWER CONTROL (3-0-0)3
Contents: Introduction, Components of hydraulic and Pneumatic control system, Energy and power in
hydraulic systems, hydraulic pumps, cylinders and motors, Hydraulic circuit design and analysis,
Electrical controls for fluid power circuits, Introduction to PLC.
Fluid power with applications by Anthony Esposito, Pearson Education
Hydraulic Control system by Herbert E Merritt, John Wiley Inc
Basic and Electro Hydraulics and Pneumatics, Festo Didactic Series
Pneumatic Systems by S R Majumdar, TMH
ME328 MACHINE DESIGN (3-1-0) 4
Fundamentals : Hooke�s law, Elastic constants, Shear force and bending moment diagram, Bending
equation, Beam deflection, Compound stress and Mohr�s circle, working stresses, modes of mechanical
failure, stress concentration, fatigue, soderberg equation, members subjected to steady and alternating
loads. Shafting, ASME design of transmission shafts, keys, design of square and rectangular key joints,
welded joints, modes of failure, strength and efficiency of the joint. Springs : stresses in coil springs of
round and square, deflection of coil springs, design of compression and tension springs.
Flexible machine elements: Flat belt, V belt drives rope drives. Gears : spur, helical, bevel, worm gear,
nomenclature, Lewis equation, Lewis form factor, design based on strength dynamic and wear loads.
Bearings: mechanism of fluid film lubrication, Journal bearing, rolling contact bearing.
K. Mahadevan and K. Balaveera Reddy “ Design and data book” (SI Units)- NITK Surathkal
V.B.Bhandary- “ Design of Machine Elements” Tata Mc.Grow Hill
Robert. L. Norton “ Design of Machinery” Mc. Graw Hill International 1992
ME350 HEAT TRANSFER (3-1-0) 4
Introduction, Conduction Heat transfer, Insulation, Fin theory, Convection Heat transfer, Natural and
Forced flow inside and out side tube, two phase heat transfer, Boiling and condensation, Heat
exchangers, Radiation heat transfer (Non participating media). Introduction to mass transfer.
Nicati M. Ozisik, Heat Transfer a Basic Approach, McGraw Hill Publication.
Holman J. P., Heat Transfer, McGraw Hill Publication.
C P Arora, Engineering Heat Transfer, Khanna Publishers, India, 1996
Frauk P Incropera, Fundamentals of Heat and Mass tranfer, John Wiley and son, Fifth edition-2002
---------------------------------------------------------------------
NITK-Course Contents(UG)2010 Page 96 of 134