English (United Kingdom) - Paul Wurth

More documents

Recommendations

Info

D et ail T o p Intertherm ® 50 High Temperature Silicone ADDITIONAL INFORMATION SAFETY PRECAUTIONS Rect Top Further information regarding industry standards, terms and abbreviations used in this data sheet can be found in the following documents available at www.international-pc.com: Definitions & Abbreviations Surface Preparation Paint Application Theoretical & Practical Coverage Individual copies of these information sections are available upon request. This product is intended for use only by professional applicators in industrial situations in accordance with the advice given on this sheet, the Material Safety Data Sheet and the container(s), and should not be used without reference to the Material Safety Data Sheet (MSDS) which International Protective Coatings has provided to its customers. All work involving the application and use of this product should be performed in compliance with all relevant national, Health, Safety & Environmental standards and regulations. In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. If in doubt regarding the suitability of use of this product, consult International Protective Coatings for further advice. PACK SIZE 5 Litre unit Intertherm 50 5 litres in a 5 litre container SHIPPING WEIGHT STORAGE Important Note 5 Gallon unit Intertherm 50 5 gallons in a 5 gallon container For availability of other pack sizes, contact International Protective Coatings. U.N. Shipping No. 1263 5 Litre unit 6.2 kg (13.7 lb) 5 Gallon unit 22.9 kg (50.5 lb) Shelf Life 12 months minimum at 25°C (77°F). Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition. Rect Bottom The information in this data sheet is not intended to be exhaustive; any person using the product for any purpose other than that specifically recommended in this data sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at their own risk. All advice given or statements made about the product (whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability at all for the performance of the product or for (subject to law) any loss or damage arising out of the use of the product. We hereby disclaim any warranties or representations, express or implied, by operation of law or otherwise, including, without limitation, any implied warranty of merchantability or fitness for a particular purpose. All products supplied and technical advice given are subject to our Conditions of Sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is liable to modification from time to time in the light of experience and our policy of continuous development. It is the user's responsibility to check with their local International Paint representative that this data sheet is current prior to using the product. Issue date: 01/08/2007 Copyright © International Paint Ltd. , International and all product names mentioned in this publication are trademarks of, or licensed to, Akzo Nobel. www.international-pc.com Page 4 of 4
Painting Paul Wurth Paint System Types FOR 519E – Appendix 4 APPENDIX 4 SUPPLIER’S DOCUMENTATION * provided by JOTUN * also consult paint supplier’s Internet home page [PKH/JMO/FOR519E APP4-00 Jotun.doc/Rev1/07-07-2010] Paul Wurth S.A. Luxembourg
Page 1 and 2:
Painting Paul Wurth Paint System Ty
Page 3 and 4:
Carboline Benelux Braak 1 · 4704 R
Page 5 and 6:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 7 and 8:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 9 and 10:
Page 11 and 12:
PAINT SYSTEM Type F, PAINT MANUFACT
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Selection & Specification Data Gene
Page 21 and 22:
.Selection & Specification Data . G
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Painting Paul Wurth Paint System Ty
Page 43 and 44:
Specification sheet Hempel (Germany
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52: Specification sheet Hempel (Germany
Page 59 and 60: HEMPADUR FAST DRY 15560 SURFACE New
Page 61 and 62: Product Data Issued: March 2009 Pag
Page 67 and 68: Product Data Issued: November 2008
Page 69 and 70: HEMPADUR MASTIC 45880/45881 Applica
Page 71 and 72: HEMPEL'S GALVOSIL 15702 SURFACE Rem
Page 73: HEMPEL’S SILICONE ALUMINIUM 56910
Page 77 and 78: HEMPADUR 85671 Issued January 2011
Page 79 and 80: HEMPADUR 85671 Microclimate: The ac
Page 81 and 82: HEMPADUR 85671 Issued January 2011
Page 83 and 84: Application Instructions Applicatio
Page 85 and 86: HEMPEL'S VINYL ESTER GF 35910 Issue
Page 87 and 88: Painting Paul Wurth Paint System Ty
Page 89 and 90: PAINT SYSTEM TYPE F * + TYPE J * PA
Page 91 and 92: E N G 0 3 0 5 Interseal 670HS S u r
Page 93 and 94: Interseal 670HS S u r f a c e T o l
Page 95 and 96: PRODUCT DESCRIPTION INTENDED USES P
Page 97 and 98: PRODUCT CHARACTERISTICS SYSTEMS COM
Page 99 and 100: Intertherm® 50 H i g h T e m p e r
Page 101: Intertherm ® 50 High Temperature S
Page 105 and 106: Technical specification Customer: P
Page 115 and 116: Technical Data Barrier 80 Product d
Page 117 and 118: Typical paint system Barrier 80 1 x
Page 119 and 120: Other surfaces The coating may be u
Page 121 and 122: Drying time Drying times are genera
Page 123 and 124: Technical Data Penguard Express Pro
Page 125 and 126: Substrate temperature 40°C Surface
Page 127 and 128: Technical Data Epoxy HR Product des
Page 129 and 130: Typical paint system Epoxy HR 2 x 1
Page 131 and 132: Shopprimed steel Clean, dry and und
Page 133 and 134: Penguard FC Page 4 of 4
Page 135 and 136: Other surfaces The coating may be u
Page 137 and 138: ISSUED 6 DECEMBER 2007 BY JOTUN THI
Page 139 and 140: Condition during application The te
show all

English (United Kingdom) - Paul Wurth

Create successful ePaper yourself

Delete template?

Save as template?