English (United Kingdom) - Paul Wurth

More documents

Recommendations

Info

DISCLAIMER The information in this data sheet is given to the best of our knowledge based on laboratory testing and practical experience. However, as the product is often used under conditions beyond our control, we cannot guarantee anything but the quality of the product itself. We reserve the right to change the given data without notice. Jotun is a World Wide company with factories, sales offices and stocks in more than 50 countries. For your nearest local Jotun address please contact the nearest regional office or visit our website at www.jotun.com ISSUED 8 JANUARY 2010 BY JOTUN THIS DATA SHEET SUPERSEDES THOSE PREVIOUSLY ISSUED Chemflake Special Page 5 of 5
Technical Data Penguard Express Product description Penguard Express is a fast drying, high solids two-pack epoxy coating which may be applied in high film thickness and at lower temperatures. Recommended use As an anti corrosive primer and/or intermediate coating for corrosion protection of steel and other substrates in athmospheric exposure where fast dry-to-recoat and/or dry-to-handle times are desired. Can be used alone or in various systems of primers and topcoats. Film thickness and spreading rate Minimum Maximum Typical Film thickness, dry (µm) 75 250 125 Film thickness, wet (µm) 100 340 170 Theoretical spreading rate (m²/l) 9,9 3 5,9 Physical properties Colour Grey, Red, Buff, Light Red Solids (vol %)* 74 ± 2 Flash point 29ºC ± 2 (Setaflash) VOC 230 gms/ltr UK-PG6/23(97). Appendix 3 Gloss Flat Gloss retention Fair Water resistance Very good Abrasion resistance Very good Solvent resistance Excellent Chemical resistance Excellent Flexibility Good *Measured according to ISO 3233:1998 (E) Note that primers used as the final coat may fade and chalk in time when exposed to sunlight and weathering effects. Colour may vary from batch to batch. If exact match to colour standards and long term cosmetic performance is needed please see our range of topcoats and finishes. Hong Kong rules: Category of paints - Other vessel coatings; VOC 260 gms/ltr HK EPD method (Ready to use); Exempt compound - N/A; Specific gravity: 1.51 kg/ltr (A+B); Both VOC and Specific gravity values provided are typical values, and will vary according to colour chosen. Surface preparation All surfaces should be clean, dry and free from contamination. The surface should be assessed and treated in accordance with ISO 8504. Penguard Express Page 1 of 4
Page 1 and 2:
Painting Paul Wurth Paint System Ty
Page 3 and 4:
Carboline Benelux Braak 1 · 4704 R
Page 5 and 6:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 7 and 8:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 9 and 10:
Page 11 and 12:
PAINT SYSTEM Type F, PAINT MANUFACT
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Selection & Specification Data Gene
Page 21 and 22:
.Selection & Specification Data . G
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Painting Paul Wurth Paint System Ty
Page 43 and 44:
Specification sheet Hempel (Germany
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
HEMPADUR FAST DRY 15560 SURFACE New
Page 61 and 62:
Product Data Issued: March 2009 Pag
Page 67 and 68:
Product Data Issued: November 2008
Page 69 and 70:
HEMPADUR MASTIC 45880/45881 Applica
Page 71 and 72: HEMPEL'S GALVOSIL 15702 SURFACE Rem
Page 73: HEMPEL’S SILICONE ALUMINIUM 56910
Page 77 and 78: HEMPADUR 85671 Issued January 2011
Page 79 and 80: HEMPADUR 85671 Microclimate: The ac
Page 81 and 82: HEMPADUR 85671 Issued January 2011
Page 83 and 84: Application Instructions Applicatio
Page 85 and 86: HEMPEL'S VINYL ESTER GF 35910 Issue
Page 87 and 88: Painting Paul Wurth Paint System Ty
Page 89 and 90: PAINT SYSTEM TYPE F * + TYPE J * PA
Page 91 and 92: E N G 0 3 0 5 Interseal 670HS S u r
Page 93 and 94: Interseal 670HS S u r f a c e T o l
Page 95 and 96: PRODUCT DESCRIPTION INTENDED USES P
Page 97 and 98: PRODUCT CHARACTERISTICS SYSTEMS COM
Page 99 and 100: Intertherm® 50 H i g h T e m p e r
Page 101 and 102: Intertherm ® 50 High Temperature S
Page 103 and 104: Painting Paul Wurth Paint System Ty
Page 105 and 106: Technical specification Customer: P
Page 115 and 116: Technical Data Barrier 80 Product d
Page 117 and 118: Typical paint system Barrier 80 1 x
Page 119 and 120: Other surfaces The coating may be u
Page 121: Drying time Drying times are genera
Page 125 and 126: Substrate temperature 40°C Surface
Page 127 and 128: Technical Data Epoxy HR Product des
Page 129 and 130: Typical paint system Epoxy HR 2 x 1
Page 131 and 132: Shopprimed steel Clean, dry and und
Page 133 and 134: Penguard FC Page 4 of 4
Page 135 and 136: Other surfaces The coating may be u
Page 137 and 138: ISSUED 6 DECEMBER 2007 BY JOTUN THI
Page 139 and 140: Condition during application The te
show all

English (United Kingdom) - Paul Wurth

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?