English (United Kingdom) - Paul Wurth

More documents

Recommendations

Info

Carbozinc Finish Application Equipment Listed below are the general equipment guidelines for the application of this product. Job site conditions may require modifications to these guidelines to achieve the desired results. General Guidelines: Spray Application Airless Spray Application June 2006 replaces April 2004 N This is a high solids coating and may require adjustments in spray techniques. Wet film thickness is easily and quickly achieved. The following spray equipment has been found suitable and is available from manufacturers such as Binks, Devibiss and Graco. Pump Ratio: 30:1 (min.) Volume Output: 2.5 gpm min. 11.5 l/min min. Material Hose: ½” I.D. min. 12.5mm min. Tip Size: Output 0.017-0.021” 0.43-0.53mm Pressure: 2100-2500 psi 135-170kg/cm² Brush For touch up use only. Use medium bristle brush and avoid rebrushing. Two coats may be required to obtain desired thickness and appearance. For best results tie-in within 5 min. Mixing & Thinning Mixing Power mix to a uniform consistency. Thinning May be thinned up to 5% by volume with Carboline Thinner #33. Pot Life Indefinite. Avoid moisture contamination. Cleanup & Safety Cleanup Use Thinner #2 or Acetone. In case of spillage, absorb and dispose of in accordance with local applicable regulations. Safety Read and follow all caution statements on this product data sheet and on the MSDS for this product. Employ normal workmanlike safety precautions. Hypersensitive persons should wear protective clothing, gloves and use protective cream on face, hands and all exposed areas. Cleanup & Safety (Cont.) Ventilation When used in enclosed areas, thorough air circulation must be used during and after application until the coating is cured. The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used. User should test and monitor exposure levels to insure all personnel are below guidelines. If not sure or if not able to monitor levels, use MSHA/NIOSH approved supplied air respirator. Application Conditions Condition Material Substrate Ambient Humidity Optimum 60°F – 85°F (16°C –29°C) 60°F-86°F (16°C-30°C) 60°F-86°F (16°C-30°C) 40-90% Minimum 40°F (4°C) 40°F (4°C) 40°F (4°C) 30% Maximum 90°F (32°C) 110°F (43°C) 110°F (43°C) 95% Industry standards are for substrate temperatures during application to be 5°F (3°C) above the dew point. This product requires moisture to complete its final cure. Use water mist if humidity is below minimums. Curing Schedule Temperature Touch Dry Dry to Handle @ 50% RH* 75°F (24°C) 15 min 2 hours These times are based on recommended coverage rates. Curing under low humidity conditions will extend times. Carbozinc inorganic zinc primers may be topcoated early with this inorganic finish. Consult Carboline Technical Service. Packaging, Handling & Storage Shipping Weight (Approximate) Flash Point (Setaflash) 1 Gallon kit 13 lbs ( kg) Carbozinc Finish Thinner 33 Thinner 2 Storage (General) Store Indoors. KEEP DRY Storage Temperature & Humidity 40 -100°F (4°C-38°C) 0-90% Relative Humidity Shelf Life 3 months at 76°F (24°C) 5 Gallon Kit 65 lbs ( kg) 66°F (19°C) 75°F (24°C) 23°F (-5°C) *Shelf Life: (actual stated shelf life) when kept at recommended storage conditions and in original unopened containers. To the best of our knowledge the Technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE, EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Carboxane® are registered trademarks of Carboline Company.
Selection & Specification Data Generic Type Phenalkamine epoxy Description High performance epoxy that has excellent resistance to fresh and salt water exposures. This coating exhibits outstanding moisture and surface tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. It contains an inert flake reinforcement (micaceous iron oxide) to enhance film strength and performance. Features Gloss Semi-gloss Color Tan Primers Self Priming · High solids, low VOC · Low temperature cure · Excellent wetting properties · Excellent surface tolerance · Excellent moisture tolerance (application) · Fast cure response · Suitable for immersion service in fresh or salt water after 60 minute cure @75°F Topcoats Acrylics, Alkyds, Epoxies, Polyurethanes Dry Film Thickness For most applications: 5-10 mils (125-250 microns) Solids Content Theoretical solids of mixed material by volume: 80 +/- 2% Theoretical Coverage Rate Dry Temp. Resistance Wet Temp. Resistance VOC Values (calculated) 1283 mil ft² ( 32 m²/l at 25 microns) 256 sq. ft. at 5 mils (6.4 sq. m/l @ 125 microns) NOTE: Material losses during mixing and applications will vary and must be taken into consideration when estimating job requirements. Continuous: 200°F (93°C) Non-Continuous: 250°F (121°C) Immersion temperature resistance depends upon exposure. Consult Carboline Technical Service for specific information. As supplied: 1.42 lbs/gal (170 g/l) mixed Thinned:16* oz/gal w/ #2: 2.06 lbs/gal (248 g/l) These are nominal values and may vary with color. HAPS Values As supplied: 1.4 lbs/solid gal Limitations Epoxies lose gloss, discolor and eventually chalk in sunlight exposure. Discoloration is more pronounced with Carbomastic 615 HS. Carbomastic 615 HS Substrates & Surface Preparation General Remove any oil or grease from surface to be coated with clean rags soaked in Carboline Thinner #2, or toluol. Concrete Do not apply coating unless concrete has cured at least 28 days @ 70°F (21°C) and 50% RH or equivalent. Substrates Steel Immersion: SSPC-SP10 with a 2.0-3.0 mil (50-75 micron) surface profile. Non-Immersion: SSPC-SP6 with a 2.0-3.0 mil (50-75 micron) surface profile for maximum protection. SSPC-SP2, SP3, SP7, or SP12 are also acceptable methods Concrete: Normally clean and dry. Remove all loose, unsound concrete. This product can tolerate damp concrete (green appearance but not visibly wet). Consult Carboline Technical Service for more specific recommendations. Ordering Information Prices may be obtained from Carboline Sales Representative or Main Office. Terms – Net 30 days. 1 Gal. Kit 5 Gal. Kit Shipping Weight 615 HS 15.8 lbs. 79 lbs. Application Equipment Listed below are the general equipment guidelines for the application of this product. Job site conditions may require modifications to these guidelines to achieve the desired results. Spray Application Airless Spray Hold gun 12-14 inches from the surface and at a right angle to the surface. Pump Ratio: 30:1 (min.) Volume Output: 9.5 l/min min. (2.5gpm min.) Material Hose: 9.5mm min. (3/8” I.D. min.) Tip Size: 0.43-0.53mm (0.017-0.021”) Output Pressure: 140-175kg/cm² (2000-2500 psi) Use a 1/2” minimum I.D. material hose The following spray equipment has been found suitable and is available from manufacturers such as Binks, DeVilbiss and Graco. Mfr. & Gun Pump* Use either model below: Huskie Graco 207-300 (DeVilbiss) Binks Model 520 Bulldog 45:1 Jupiter 8D *Teflon packings are recommended and available from pump manufacturer. December 2008 To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE, EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Carboguard® are registered trademarks of Carboline Company.
Page 1 and 2: Painting Paul Wurth Paint System Ty
Page 3 and 4: Carboline Benelux Braak 1 · 4704 R
Page 5 and 6: PAINT SYSTEM Type C, PAINT MANUFACT
Page 7 and 8: PAINT SYSTEM Type C, PAINT MANUFACT
Page 11 and 12: PAINT SYSTEM Type F, PAINT MANUFACT
Page 19 and 20: Selection & Specification Data Gene
Page 21 and 22: .Selection & Specification Data . G
Page 35: Selection & Specification Data Gene
Page 41 and 42: Painting Paul Wurth Paint System Ty
Page 43 and 44: Specification sheet Hempel (Germany
Page 59 and 60: HEMPADUR FAST DRY 15560 SURFACE New
Page 61 and 62: Product Data Issued: March 2009 Pag
Page 67 and 68: Product Data Issued: November 2008
Page 69 and 70: HEMPADUR MASTIC 45880/45881 Applica
Page 71 and 72: HEMPEL'S GALVOSIL 15702 SURFACE Rem
Page 73: HEMPEL’S SILICONE ALUMINIUM 56910
Page 77 and 78: HEMPADUR 85671 Issued January 2011
Page 79 and 80: HEMPADUR 85671 Microclimate: The ac
Page 81 and 82: HEMPADUR 85671 Issued January 2011
Page 83 and 84: Application Instructions Applicatio
Page 85 and 86: HEMPEL'S VINYL ESTER GF 35910 Issue
Page 87 and 88:
Painting Paul Wurth Paint System Ty
Page 89 and 90:
PAINT SYSTEM TYPE F * + TYPE J * PA
Page 91 and 92:
E N G 0 3 0 5 Interseal 670HS S u r
Page 93 and 94:
Interseal 670HS S u r f a c e T o l
Page 95 and 96:
PRODUCT DESCRIPTION INTENDED USES P
Page 97 and 98:
PRODUCT CHARACTERISTICS SYSTEMS COM
Page 99 and 100:
Intertherm® 50 H i g h T e m p e r
Page 101 and 102:
Intertherm ® 50 High Temperature S
Page 103 and 104:
Painting Paul Wurth Paint System Ty
Page 105 and 106:
Technical specification Customer: P
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Technical Data Barrier 80 Product d
Page 117 and 118:
Typical paint system Barrier 80 1 x
Page 119 and 120:
Other surfaces The coating may be u
Page 121 and 122:
Drying time Drying times are genera
Page 123 and 124:
Technical Data Penguard Express Pro
Page 125 and 126:
Substrate temperature 40°C Surface
Page 127 and 128:
Technical Data Epoxy HR Product des
Page 129 and 130:
Typical paint system Epoxy HR 2 x 1
Page 131 and 132:
Shopprimed steel Clean, dry and und
Page 133 and 134:
Penguard FC Page 4 of 4
Page 135 and 136:
Other surfaces The coating may be u
Page 137 and 138:
ISSUED 6 DECEMBER 2007 BY JOTUN THI
Page 139 and 140:
Condition during application The te
show all

English (United Kingdom) - Paul Wurth

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?