English (United Kingdom) - Paul Wurth

More documents

Recommendations

Info

Product Data Issued: December 2007 Page 1 of 2 HEMPEL’S SILICONE ALUMINIUM 56910 Description: HEMPEL’S SILICONE ALUMINIUM 56910 is a heat resistant aluminium pigmented polysiloxane paint. Recommended use: For long-term protection of hot pipelines, exhaust pipes, smoke stacks and other hot surfaces. In corrosive environment see PRECEDING COAT overleaf. Service temperatures: Maximum, dry exposure only: 600°C/1112°F. Certificates/Approvals: Complies with EU Directive 2004/42/EC, subcategory i (see REMARKS overleaf). Availability: Part of Group Assortment. Local availability subject to confirmation. PHYSICAL CONSTANTS Colours/Shade nos: Aluminium/19000 Finish: Semi-flat (See REMARKS overleaf) Volume solids, %: 35 ± 1 Theoretical spreading rate: 14.0 m²/litre - 25 micron 561 sq.ft./US gallon - 1.0 mil Flash point: 25°C/77°F Specific gravity: 1.1 kg/litre - 9.2 lbs/US gallon Surface dry: 1 (approx.) hour at 20°C/68°F (ISO 1517) Dry to touch: 2-4 hours at 20°C/68°F V.O.C.: 585 g/litre - 4.9 lbs/US gallon The physical constants stated are nominal data according to the HEMPEL Group's approved formulas. They are subject to normal manufacturing tolerances and where stated, being standard deviation according to ISO 3534-1. APPLICATION DETAILS: Application method: Airless spray Air spray Brush Thinner (max.vol.): 08080 (5%) 08080 (15%) 08080 (5%) (See REMARKS overleaf) Nozzle orifice: .017" Nozzle pressure: 125 bar/1800 psi (Airless spray data are indicative and subject to adjustment) Cleaning of tools: THINNER 08080 Indicated film thickness, dry: 25 micron/1 mil (See REMARKS overleaf) Indicated film thickness, wet: 75 micron/3 mils Recoat interval, min: 24 hours (20°C/68°F) (See REMARKS overleaf) Recoat interval, max: See REMARKS overleaf Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult HEMPEL Material Safety Data Sheets and follow all local or national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only in well ventilated areas. HEMPEL Product Data Sheet
HEMPEL’S SILICONE ALUMINIUM 56910 SURFACE Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other PREPARATION: contaminants by (high pressure) fresh water cleaning. Abrasive blasting to Sa 2½. APPLICATION Clean and dry surface with a temperature above the dew point to avoid condensation. In confined CONDITIONS: spaces provide adequate ventilation during application and drying. PRECEDING Can be used directly on blast-cleaned steel. For maximum corrosion protection, a primer coat of COAT: one of the following paints is recommended (40 micron/1.6 mil dry film thicknesses): HEMPEL’S SILICONE ZINC 16900 or HEMPEL’S GALVOSIL 15700. This will lower the heat resistance; reference is made to the product data sheets for the mentioned primers. SUBSEQUENT None. COAT: REMARKS: VOC - EU directive As supplied 5 vol. % thinning Limit phase I, 2007 Limit phase II, 2010 2004/42/EC: VOC in g/l 585 595 600 500 Gloss: After exposure to heat the gloss is reduced. Thermo plasticity: The paint film is somewhat thermoplastic also after heating. Film thicknesses: It is recommended to avoid too high thicknesses of the paint as this will give a risk of blistering at later heating. THINNER 08080 must be added at application to secure the low dry film thickness. High temperature For high temperature service, the total dry film thickness of HEMPEL’S SILICONE ALUMINIUM service: 56910 should preferably be kept at 75 micron/3 mils as maximum. First exposure On first exposure to heat the temperature increase from ambient temperature to the required to heat: service temperature must run over a period of 24 hours. Curing: The coating will be fully cured after: 3 days at 100°C/212°F, 1 day at 150°C/302°F, or 2 hours at 200°C/392°F. Recoating: May be recoated when through dry (24 hours at 20°C/68°F) or after being heated for one hour to approximately 200°C/392°F. Before recoating after exposure in contaminated environment, clean surface thoroughly by high pressure fresh water hosing and allow to dry. Zinc silicate primer: If HEMPEL’S SILICONE ALUMINIUM 56910 is applied on zinc silicate coatings, such as HEMPEL’S GALVOSIL 15700, popping may occur after application or after first heating up. The best way to avoid popping is to apply a mist coat in the first pass of HEMPEL’S SILICONE ALUMINIUM 56910. Let the air escape and apply the full coat of HEMPEL'S SILICONE ALUMINIUM 56910. Note: HEMPEL’S SILICONE ALUMINIUM 56910 is for professional use only. ISSUED BY: HEMPEL A/S - 5691019000CO004 This Product Data Sheet supersedes those previously issued. This For explanations, Product Data definitions Sheet supersedes and scope, those see previously “Explanatory issued. Notes” in the HEMPEL Book. For Data, explanations, specifications, definitions directions and and scope, recommendations see “Explanatory given Notes” in this in data the sheet HEMPEL represent Book. only test results or Data, experience specifications, obtained under directions controlled and recommendations or specially defined given circumstances. in this data Their sheet accuracy, represent completeness only test results or or experience appropriateness obtained under under the actual controlled conditions or specially of any defined intended circumstances. use of the Products Their herein accuracy, must completeness be determined or appropriateness exclusively by the under Buyer the and/or actual User. conditions of any intended use of the Products herein must be determined The exclusively Products by are the supplied Buyer and/or and all User. technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF The SALES, Products DELIVERY are supplied AND SERVICE, and all technical unless otherwise assistance expressly is given agreed subject in writing. to HEMPEL's The Manufacturer GENERAL CONDITIONS and Seller OF SALES, disclaim, DELIVERY and Buyer AND and/or SERVICE, User waive unless all otherwise claims involving, expressly any agreed liability, in writing. including The but Manufacturer not limited to and negligence, Seller disclaim, except as and expressed Buyer and/or in said User GENERAL waive CONDITIONS all claims involving, for all results, any liability, injury including or direct or but consequential not limited to losses negligence, or except damages as arising expressed from in the said use GENERAL of the Products CONDITIONS as recommended for all results, above, injury on or the direct overleaf or consequential or otherwise. losses or damages Product data arising are subject from theto use change of thewithout Products notice as recommended and become void above, five on years thefrom overleaf the date or otherwise. of issue. Issued: December 2007 Page 2 of 2 Product Data Sheet
Page 1 and 2:
Painting Paul Wurth Paint System Ty
Page 3 and 4:
Carboline Benelux Braak 1 · 4704 R
Page 5 and 6:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 7 and 8:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 9 and 10:
Page 11 and 12:
PAINT SYSTEM Type F, PAINT MANUFACT
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Selection & Specification Data Gene
Page 21 and 22: .Selection & Specification Data . G
Page 23 and 24: Selection & Specification Data Gene
Page 41 and 42: Painting Paul Wurth Paint System Ty
Page 43 and 44: Specification sheet Hempel (Germany
Page 59 and 60: HEMPADUR FAST DRY 15560 SURFACE New
Page 61 and 62: Product Data Issued: March 2009 Pag
Page 67 and 68: Product Data Issued: November 2008
Page 69 and 70: HEMPADUR MASTIC 45880/45881 Applica
Page 71: HEMPEL'S GALVOSIL 15702 SURFACE Rem
Page 77 and 78: HEMPADUR 85671 Issued January 2011
Page 79 and 80: HEMPADUR 85671 Microclimate: The ac
Page 81 and 82: HEMPADUR 85671 Issued January 2011
Page 83 and 84: Application Instructions Applicatio
Page 85 and 86: HEMPEL'S VINYL ESTER GF 35910 Issue
Page 89 and 90: PAINT SYSTEM TYPE F * + TYPE J * PA
Page 91 and 92: E N G 0 3 0 5 Interseal 670HS S u r
Page 93 and 94: Interseal 670HS S u r f a c e T o l
Page 95 and 96: PRODUCT DESCRIPTION INTENDED USES P
Page 97 and 98: PRODUCT CHARACTERISTICS SYSTEMS COM
Page 99 and 100: Intertherm® 50 H i g h T e m p e r
Page 101 and 102: Intertherm ® 50 High Temperature S
Page 105 and 106: Technical specification Customer: P
Page 115 and 116: Technical Data Barrier 80 Product d
Page 117 and 118: Typical paint system Barrier 80 1 x
Page 119 and 120: Other surfaces The coating may be u
Page 121 and 122: Drying time Drying times are genera
Page 123 and 124:
Technical Data Penguard Express Pro
Page 125 and 126:
Substrate temperature 40°C Surface
Page 127 and 128:
Technical Data Epoxy HR Product des
Page 129 and 130:
Typical paint system Epoxy HR 2 x 1
Page 131 and 132:
Shopprimed steel Clean, dry and und
Page 133 and 134:
Penguard FC Page 4 of 4
Page 135 and 136:
Other surfaces The coating may be u
Page 137 and 138:
ISSUED 6 DECEMBER 2007 BY JOTUN THI
Page 139 and 140:
Condition during application The te
show all

English (United Kingdom) - Paul Wurth

Create successful ePaper yourself

Delete template?

Save as template?