English (United Kingdom) - Paul Wurth

More documents

Recommendations

Info

Technical specification Customer: Paul Wurth S.A. Project: Paul Wurth Paint Systems Standard/ FOR 519E / Rev 6 Version: Location: Position: Paint System stack Area: 10 m2 System: Date: 06.07.2010 Prepared by: Christian Boge Checked by: Issued by Jotun Pretreatment: All areas to be cleaned thoroughly with strong detergents and high pressure fresh water to remove oil, grease, salt and contaminations. All areas to be blastcleaned to Sa 2½ (ISO 8501-1:1988). Filmthickness (µm) Recoating intervals Coat Product no. Area to paint Vol. solids Dry spec. Wet spec. Loss (%) 23°C 40°C Thinner Consumption incl. loss % % Min Max Min Max No. Max% m2/ltr Total ltr. 1 Chemflake Special, red 100 96 600 0 4 h 24 h 2 h 12 h Styrene 0 1,6 6 2 Chemflake Special, white 100 96 600 625 625 0 4 h 24 h 2 h 12 h Styrene 0 1,6 6 1200 * please refer to the relevant technical datasheets for recoating and curing conditions Remarks: Unless otherwise agreed in writing, all product supplied and technical advice given by us are subject to our standard terms and conditions of sale. In the event that supplies are made and technical advice is given by one of our associated companies or dealers, then such supplies and technical advice shall be subject to the standard terms of sale of that company, a copy of which is available upon request. The given data must be considered as guidelines only, the figures in some colums may be rounded. Drying times and paint consumptions may vary depending on actual conditions. For updated information about our products please refer to our web site at www.jotun.com Printed 06.07.2010 17:40:56 Page 11
Technical Data Barrier 80 Product description Barrier 80 is a two-pack zinc rich epoxy primer with a high content of zinc that complies with the compositional requirements for SSPC Paint 20 level 2 and ISO 12944. Can also be made to order with ASTM D520 Type II zinc dust. Recommended use As a zinc rich primer on blast cleaned steel. Barrier 80 is used in combination with advanced coating systems to further improve protection against corrosion. Film thickness and spreading rate Minimum Maximum Typical Film thickness, dry (µm) 40 90 50 Film thickness, wet (µm) 65 150 80 Theoretical spreading rate (m²/l) 15,3 6,8 12,2 Comments In a systems of DFT of max. 90 µm, the drying time will increase. To achieve a uniform, closed film at dry film thickness below 40 microns it will be necessary to thin Barrier 80 with Jotun Thinner No. 17. Physical properties Colour Grey Solids (vol %)* 61 ± 2 Flash point 27ºC ± 2 (Setaflash) VOC 365 gms/ltr UK-PG6/23(97). Appendix 3 Gloss Flat Water resistance Excellent Abrasion resistance Very good Solvent resistance Very good Flexibility Good *Measured according to ISO 3233:1998 (E) Surface preparation All surfaces should be clean, dry and free from contamination. The surface should be assessed and treated in accordance with ISO 8504. Bare steel Cleanliness: Blast cleaning to min. Sa 2 ½ (ISO 8501-1:2007) or for maintenance UHPWJ to WJ2 (NACE No.5/SSPC- SP 12). Roughness: using abrasives suitable to achieve minimum grade Fine (ISO 8503-2). Shopprimed steel Clean, dry and undamaged approved shopprimer. Barrier 80 Page 1 of 3
Page 1 and 2:
Painting Paul Wurth Paint System Ty
Page 3 and 4:
Carboline Benelux Braak 1 · 4704 R
Page 5 and 6:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 7 and 8:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 9 and 10:
Page 11 and 12:
PAINT SYSTEM Type F, PAINT MANUFACT
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Selection & Specification Data Gene
Page 21 and 22:
.Selection & Specification Data . G
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Painting Paul Wurth Paint System Ty
Page 43 and 44:
Specification sheet Hempel (Germany
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
HEMPADUR FAST DRY 15560 SURFACE New
Page 61 and 62:
Product Data Issued: March 2009 Pag
Page 67 and 68: Product Data Issued: November 2008
Page 69 and 70: HEMPADUR MASTIC 45880/45881 Applica
Page 71 and 72: HEMPEL'S GALVOSIL 15702 SURFACE Rem
Page 73: HEMPEL’S SILICONE ALUMINIUM 56910
Page 77 and 78: HEMPADUR 85671 Issued January 2011
Page 79 and 80: HEMPADUR 85671 Microclimate: The ac
Page 81 and 82: HEMPADUR 85671 Issued January 2011
Page 83 and 84: Application Instructions Applicatio
Page 85 and 86: HEMPEL'S VINYL ESTER GF 35910 Issue
Page 87 and 88: Painting Paul Wurth Paint System Ty
Page 89 and 90: PAINT SYSTEM TYPE F * + TYPE J * PA
Page 91 and 92: E N G 0 3 0 5 Interseal 670HS S u r
Page 93 and 94: Interseal 670HS S u r f a c e T o l
Page 95 and 96: PRODUCT DESCRIPTION INTENDED USES P
Page 97 and 98: PRODUCT CHARACTERISTICS SYSTEMS COM
Page 99 and 100: Intertherm® 50 H i g h T e m p e r
Page 101 and 102: Intertherm ® 50 High Temperature S
Page 103 and 104: Painting Paul Wurth Paint System Ty
Page 105 and 106: Technical specification Customer: P
Page 113: Technical specification Customer: P
Page 117 and 118: Typical paint system Barrier 80 1 x
Page 119 and 120: Other surfaces The coating may be u
Page 121 and 122: Drying time Drying times are genera
Page 123 and 124: Technical Data Penguard Express Pro
Page 125 and 126: Substrate temperature 40°C Surface
Page 127 and 128: Technical Data Epoxy HR Product des
Page 129 and 130: Typical paint system Epoxy HR 2 x 1
Page 131 and 132: Shopprimed steel Clean, dry and und
Page 133 and 134: Penguard FC Page 4 of 4
Page 135 and 136: Other surfaces The coating may be u
Page 137 and 138: ISSUED 6 DECEMBER 2007 BY JOTUN THI
Page 139 and 140: Condition during application The te
show all

English (United Kingdom) - Paul Wurth

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?