English (United Kingdom) - Paul Wurth

More documents

Recommendations

Info

Product Data Issued: December 2007 Page 1 of 3 HEMPADUR FAST DRY 15560 BASE 15569 with CURING AGENT 97560 Description: HEMPADUR FAST DRY 15560 is a two-component, polyamine adduct cured epoxy paint with a very short drying time. Contains zinc phosphate. Recommended use: As a quick drying primer or intermediate coat in HEMPADUR systems for especially fast recoatable in-shop applications. Can be used for on-site work too if eg VOC compliance is requested. Service temperatures: Maximum, dry exposure only: 140°C/284°F. See REMARKS overleaf. Certificates/Approvals: Complies with EU Directive 2004/42/EC, subcategory j. See REMARKS overleaf. Availability: Part of Group Assortment. Local availability subject to confirmation. PHYSICAL CONSTANTS: Colours/Shade nos: Grey 12170 - Reddish grey/12430* (MIO version) (See REMARKS overleaf) Finish: Flat Volume solids, %: 62 ± 1 Theoretical spreading rate: 6.2 m²/litre - 100 micron 249 sq.ft./US gallon - 4 mils Flash point: 27°C/81°F Specific gravity: 1.5 kg/litre - 12.5 lbs/US gallon Surface dry: ½ (approx.) hr at 20°C/68°F (ISO 1517) Dry to touch: 1-1½ hour at 20°C/68°F Fully cured: 7 days at 20°C/68°F V.O.C.: 330 g/litre - 2.7 lbs/US gallon (According to EPA Fed Ref Method 24) 355 g/litre - 3.0 lbs/US gallon *Another shade: red 50630 may be available according to assortment list. The physical constants stated are nominal data according to the HEMPEL Group's approved formulas. They are subject to normal manufacturing tolerances and where stated, being standard deviation according to ISO 3534-1. APPLICATION DETAILS: Mixing ratio for 15560: Base 15569 : Curing agent 97560 4 : 1 by volume Application method: Airless spray Air Spray Brush Thinner (max. vol.): 08450 (5%) 08450 (15%) 08450 (5%) Pot life: 2 hours (20°C/68°F) Nozzle orifice: .019"-.021" Nozzle pressure: 175 bar/2500 psi (Airless spray data are indicative and subject to adjustment) Cleaning of tools: HEMPEL’S TOOL CLEANER 99610 Indicated film thickness, dry: 100 micron/4 mils (See REMARKS overleaf) Indicated film thickness, wet: 175 micron/7 mils Recoat interval, min: See REMARKS overleaf Recoat interval, max: See REMARKS overleaf Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult HEMPEL Material Safety Data Sheets and follow all local or national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only in well ventilated areas. HEMPEL Product Data Sheet
HEMPADUR FAST DRY 15560 SURFACE New steel (dry conditions): Abrasive blasting to Sa 2½. For temporary protection, if required, use PREPARATION: suitable shopprimer. All damage of shopprimer and contamination from storage and fabrication should be thoroughly cleaned prior to final painting. For repair and touch-up use HEMPADUR 15560. Maintenance: Remove oil and grease, etc. with suitable detergent. Remove salt and other contaminants by (high pressure) fresh water cleaning. Remove all rust and loose material by wet or dry abrasive blasting or power tool cleaning. Feather edges to sound and intact areas. After wet abrasive blasting hose down the surface with fresh water and allow drying. Touch up bare spots to full film thickness. APPLICATION Use only where application and curing can proceed at temperatures above 0°C/32°F. CONDITIONS: The temperature of the paint itself should be 15°C/60°F or above to secure proper application properties. In confined spaces provide adequate ventilation during application and drying. PRECEDING COAT: None, or according to specification. SUBSEQUENT COAT: HEMPADUR, HEMPATHANE, HEMPATEX or HEMUCRYL as per specification. REMARKS: VOC - EU directive As supplied 15 vol. % thinning Limit phase I, 2007 Limit phase II, 2010 2004/42/EC: VOC in g/l 355 420 550 500 VOC: For VOC of other shades, please refer to Safety Data Sheet. Shade: CURING AGENT 97560 will become darker during storage. This will result in a darker and more yellowish shade than grey 12170. The colour change will have no influence on the performance. Weathering/ The natural tendency of epoxy coatings to chalk in outdoor exposure and to become more service sensitive to mechanical damage and chemical exposure at elevated temperatures is also temperatures: reflected in this product. Film thicknesses: May be specified in another film thickness than indicated depending on purpose and area of use. This will alter spreading rate and may influence drying time and recoating interval. Normal range is 75-150 micron/3-6 mils. Irregular surfaces: Special care should be taken in relation to irregular surfaces (welding seams, undercuts etc.) as application with an excessive film thickness - typically being more than 400 micron/16 mils per coat - may result in cracking especially on such areas. Recoating: Recoating intervals related to later conditions of exposure: (Dry film thickness of HEMPADUR FAST DRY 15560 as indicated below) Issued: December 2007 Page 2 of 3 Minimum In-field application* 100 micron/4 mils Minimum Workshop application 75 micron/3 mils Maximum** Surface temperature 20°C/68°F 20°C/68°F 20°C/68°F Exposure during service Atmospheric Atmospheric Atmospheric Recoated with Medium Severe Medium Severe Medium Severe HEMPATEX 1 hour 2 hours 15 minutes 1 hour 8 hours 8 hours HEMPADUR 2 hours 3 hours 1 hour 1½ hours None None HEMPATHANE 2 hours 3 hours 1 hour 1½ hours 10 days 3 days 58030 1 hour 2 hours 1 hour 1½ hours 24 hours 8 hours *In case of general maintenance involving epoxy systems of high total dry film thickness, the minimum recoating interval may advantageously be doubled up. ** For mild atmospheric exposure recoating with HEMPADUR and HEMPATHANE qualities has no maximum. For other qualities please contact HEMPEL. If the maximum recoating interval is exceeded, whatever the subsequent coat, roughening of the surface is necessary to ensure optimum intercoat adhesion or in the case of recoating with coatings other than HEMPADUR, apply a (thin) additional coat of HEMPADUR FAST DRY 15560 within the above directions for recoating. A completely clean surface is mandatory to ensure intercoat adhesion, especially in the case of long recoating intervals. Any dirt, oil and grease have to be removed with eg suitable detergent followed by high pressure fresh water cleaning. Salts to be removed by fresh water hosing. Any degraded surface layer, as a result of a long exposure period, must be removed as well. Product Data Sheet
Page 1 and 2:
Painting Paul Wurth Paint System Ty
Page 3 and 4:
Carboline Benelux Braak 1 · 4704 R
Page 5 and 6:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 7 and 8: PAINT SYSTEM Type C, PAINT MANUFACT
Page 9 and 10: Carboline Benelux Braak 1 · 4704 R
Page 11 and 12: PAINT SYSTEM Type F, PAINT MANUFACT
Page 17 and 18: Carboline Benelux Braak 1 · 4704 R
Page 19 and 20: Selection & Specification Data Gene
Page 21 and 22: .Selection & Specification Data . G
Page 41 and 42: Painting Paul Wurth Paint System Ty
Page 43 and 44: Specification sheet Hempel (Germany
Page 57: Specification sheet Hempel (Germany
Page 61 and 62: Product Data Issued: March 2009 Pag
Page 67 and 68: Product Data Issued: November 2008
Page 69 and 70: HEMPADUR MASTIC 45880/45881 Applica
Page 71 and 72: HEMPEL'S GALVOSIL 15702 SURFACE Rem
Page 73: HEMPEL’S SILICONE ALUMINIUM 56910
Page 77 and 78: HEMPADUR 85671 Issued January 2011
Page 79 and 80: HEMPADUR 85671 Microclimate: The ac
Page 81 and 82: HEMPADUR 85671 Issued January 2011
Page 83 and 84: Application Instructions Applicatio
Page 85 and 86: HEMPEL'S VINYL ESTER GF 35910 Issue
Page 89 and 90: PAINT SYSTEM TYPE F * + TYPE J * PA
Page 91 and 92: E N G 0 3 0 5 Interseal 670HS S u r
Page 93 and 94: Interseal 670HS S u r f a c e T o l
Page 95 and 96: PRODUCT DESCRIPTION INTENDED USES P
Page 97 and 98: PRODUCT CHARACTERISTICS SYSTEMS COM
Page 99 and 100: Intertherm® 50 H i g h T e m p e r
Page 101 and 102: Intertherm ® 50 High Temperature S
Page 105 and 106: Technical specification Customer: P
Page 107 and 108: Technical specification Customer: P
Page 109 and 110:
Technical specification Customer: P
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Technical Data Barrier 80 Product d
Page 117 and 118:
Typical paint system Barrier 80 1 x
Page 119 and 120:
Other surfaces The coating may be u
Page 121 and 122:
Drying time Drying times are genera
Page 123 and 124:
Technical Data Penguard Express Pro
Page 125 and 126:
Substrate temperature 40°C Surface
Page 127 and 128:
Technical Data Epoxy HR Product des
Page 129 and 130:
Typical paint system Epoxy HR 2 x 1
Page 131 and 132:
Shopprimed steel Clean, dry and und
Page 133 and 134:
Penguard FC Page 4 of 4
Page 135 and 136:
Other surfaces The coating may be u
Page 137 and 138:
ISSUED 6 DECEMBER 2007 BY JOTUN THI
Page 139 and 140:
Condition during application The te
show all

English (United Kingdom) - Paul Wurth

Create successful ePaper yourself

Delete template?

Save as template?