English (United Kingdom) - Paul Wurth

More documents

Recommendations

Info

HEMPEL'S VINYL ESTER GF 35910 The repair process: General: Before mechanical treatment, surfaces to be repaired have to be cleaned for any salts and other contamination. Issued: March 2010 Page 4 of 4 Small areas and single pinholes. The surface preparation can be executed by grinding to a clean rough metal surface, feathering edges of intact coating and slightly sanding the adjacent surface. Pinholes are best treated by using a 3 mm flat bottomed drill to enlarge the pinhole down to the substrate. Clean and wash with HEMPEL’S THINNER 08450. Work HEMPEL’S VINYL ESTER GF 35910 into the hole before brushing a small amount of the material over the top and immediately surrounding zone. Ensure that the specified total thickness is achieved. Larger areas or areas with extensive pin holing. Treatment: Repeat the original specification. Shelf life Shelf life is dependent on storage temperature. Shelf life is reduced at storage temperatures above 20°C/68°F. HEMPEL’S VINYL ESTER GF 35910 should never be stored in direct sunlight. It is recommended to keep the storage temperature a low as possible - if necessary via refrigeration. Recommended storage temperature is 5 - 20°C (41 - 68°F). Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult HEMPEL Material Safety Data Sheets and follow all local or national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only in well ventilated areas. ISSUED BY: HEMPEL A/S - 3591011630 This Product Data Sheet supersedes those previously issued. For explanations, definitions and scope, see “Explanatory Notes” in the HEMPEL Book. Data, specifications, directions and recommendations given in this data sheet represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions of any intended use of the Products herein must be determined exclusively by the Buyer and/or User. The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise. Product data are subject to change without notice and become void five years from the date of issue. Application Instructions
Painting Paul Wurth Paint System Types FOR 519E – Appendix 2 APPENDIX 2 SUPPLIER’S DOCUMENTATION * provided by INTERNATIONAL * also consult paint supplier’s Internet home page [CSR/CSR/FOR519E APP3-00 International.doc/Rev0/22-09-2009] Paul Wurth S.A. Luxembourg
Page 1 and 2:
Painting Paul Wurth Paint System Ty
Page 3 and 4:
Carboline Benelux Braak 1 · 4704 R
Page 5 and 6:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 7 and 8:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 9 and 10:
Page 11 and 12:
PAINT SYSTEM Type F, PAINT MANUFACT
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Selection & Specification Data Gene
Page 21 and 22:
.Selection & Specification Data . G
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36: Selection & Specification Data Gene
Page 41 and 42: Painting Paul Wurth Paint System Ty
Page 43 and 44: Specification sheet Hempel (Germany
Page 59 and 60: HEMPADUR FAST DRY 15560 SURFACE New
Page 61 and 62: Product Data Issued: March 2009 Pag
Page 67 and 68: Product Data Issued: November 2008
Page 69 and 70: HEMPADUR MASTIC 45880/45881 Applica
Page 71 and 72: HEMPEL'S GALVOSIL 15702 SURFACE Rem
Page 73: HEMPEL’S SILICONE ALUMINIUM 56910
Page 77 and 78: HEMPADUR 85671 Issued January 2011
Page 79 and 80: HEMPADUR 85671 Microclimate: The ac
Page 81 and 82: HEMPADUR 85671 Issued January 2011
Page 83 and 84: Application Instructions Applicatio
Page 85: HEMPEL'S VINYL ESTER GF 35910 Issue
Page 89 and 90: PAINT SYSTEM TYPE F * + TYPE J * PA
Page 91 and 92: E N G 0 3 0 5 Interseal 670HS S u r
Page 93 and 94: Interseal 670HS S u r f a c e T o l
Page 95 and 96: PRODUCT DESCRIPTION INTENDED USES P
Page 97 and 98: PRODUCT CHARACTERISTICS SYSTEMS COM
Page 99 and 100: Intertherm® 50 H i g h T e m p e r
Page 101 and 102: Intertherm ® 50 High Temperature S
Page 103 and 104: Painting Paul Wurth Paint System Ty
Page 105 and 106: Technical specification Customer: P
Page 115 and 116: Technical Data Barrier 80 Product d
Page 117 and 118: Typical paint system Barrier 80 1 x
Page 119 and 120: Other surfaces The coating may be u
Page 121 and 122: Drying time Drying times are genera
Page 123 and 124: Technical Data Penguard Express Pro
Page 125 and 126: Substrate temperature 40°C Surface
Page 127 and 128: Technical Data Epoxy HR Product des
Page 129 and 130: Typical paint system Epoxy HR 2 x 1
Page 131 and 132: Shopprimed steel Clean, dry and und
Page 133 and 134: Penguard FC Page 4 of 4
Page 135 and 136: Other surfaces The coating may be u
Page 137 and 138:
ISSUED 6 DECEMBER 2007 BY JOTUN THI
Page 139 and 140:
Condition during application The te
show all

English (United Kingdom) - Paul Wurth

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?