English (United Kingdom) - Paul Wurth

More documents

Recommendations

Info

ISSUED 26 MAY 2010 BY JOTUN THIS DATA SHEET SUPERSEDES THOSE PREVIOUSLY ISSUED Penguard Express Page 4 of 4
Technical Data Epoxy HR Product description Epoxy HR is a two-component, high solid phenolic epoxy coating with high heat resistance. Recommended use Corrosion protection for external areas of pipes and other steelwork exposed to high temperatures (up to 200ºC). Also suitable for application to hot substrates (up to 150ºC). Note that Epoxy HR may change colour at elevated temperatures. Epoxy HR is also suitable for prevention of corrosion under insulation up to 200ºC, please contact Jotun for details of acceptable conditions. Film thickness and spreading rate Minimum Maximum Typical Film thickness, dry (µm) 100 200 125 Film thickness, wet (µm) 160 320 200 Theoretical spreading rate (m²/l) 6,3 3,2 5 Physical properties Colour Aluminium, Light Grey Solids (vol %)* 63 ± 2 Flash point 28ºC ± 2 (Setaflash) VOC 310 gms/ltr UK-PG6/23(97). Appendix 3 Gloss Flat Water resistance Very good Solvent resistance Excellent Chemical resistance Excellent Flexibility Fair *Measured according to ISO 3233:1998 (E) Surface preparation All surfaces should be clean, dry and free from contamination. The surface should be assessed and treated in accordance with ISO 8504. Bare steel Cleanliness: Power tool cleaning to min. St 2, mill scale free (ISO 8501-1:2007) and a roughness between 35 - 50 microns. Improved surface treatment (blast cleaning to Sa 2½) will improve the performance. Other surfaces The coating may be used on other substrates. Please contact your local Jotun office for more information. Epoxy HR Page 1 of 3
Page 1 and 2:
Painting Paul Wurth Paint System Ty
Page 3 and 4:
Carboline Benelux Braak 1 · 4704 R
Page 5 and 6:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 7 and 8:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 9 and 10:
Page 11 and 12:
PAINT SYSTEM Type F, PAINT MANUFACT
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Selection & Specification Data Gene
Page 21 and 22:
.Selection & Specification Data . G
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Painting Paul Wurth Paint System Ty
Page 43 and 44:
Specification sheet Hempel (Germany
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
HEMPADUR FAST DRY 15560 SURFACE New
Page 61 and 62:
Product Data Issued: March 2009 Pag
Page 67 and 68:
Product Data Issued: November 2008
Page 69 and 70:
HEMPADUR MASTIC 45880/45881 Applica
Page 71 and 72:
HEMPEL'S GALVOSIL 15702 SURFACE Rem
Page 73:
HEMPEL’S SILICONE ALUMINIUM 56910
Page 77 and 78: HEMPADUR 85671 Issued January 2011
Page 79 and 80: HEMPADUR 85671 Microclimate: The ac
Page 81 and 82: HEMPADUR 85671 Issued January 2011
Page 83 and 84: Application Instructions Applicatio
Page 85 and 86: HEMPEL'S VINYL ESTER GF 35910 Issue
Page 87 and 88: Painting Paul Wurth Paint System Ty
Page 89 and 90: PAINT SYSTEM TYPE F * + TYPE J * PA
Page 91 and 92: E N G 0 3 0 5 Interseal 670HS S u r
Page 93 and 94: Interseal 670HS S u r f a c e T o l
Page 95 and 96: PRODUCT DESCRIPTION INTENDED USES P
Page 97 and 98: PRODUCT CHARACTERISTICS SYSTEMS COM
Page 99 and 100: Intertherm® 50 H i g h T e m p e r
Page 101 and 102: Intertherm ® 50 High Temperature S
Page 103 and 104: Painting Paul Wurth Paint System Ty
Page 105 and 106: Technical specification Customer: P
Page 115 and 116: Technical Data Barrier 80 Product d
Page 117 and 118: Typical paint system Barrier 80 1 x
Page 119 and 120: Other surfaces The coating may be u
Page 121 and 122: Drying time Drying times are genera
Page 123 and 124: Technical Data Penguard Express Pro
Page 125: Substrate temperature 40°C Surface
Page 129 and 130: Typical paint system Epoxy HR 2 x 1
Page 131 and 132: Shopprimed steel Clean, dry and und
Page 133 and 134: Penguard FC Page 4 of 4
Page 135 and 136: Other surfaces The coating may be u
Page 137 and 138: ISSUED 6 DECEMBER 2007 BY JOTUN THI
Page 139 and 140: Condition during application The te
show all

English (United Kingdom) - Paul Wurth

Create successful ePaper yourself

Delete template?

Save as template?