English (United Kingdom) - Paul Wurth

More documents

Recommendations

Info

Technical Data Chemflake Special Product description Chemflake Special is a high build glass flake reinforced vinyl ester coating, specially designed for high temperature service. Recommended use Steel in aggressive environments. For maximum corrosion and chemical protection also in high temperature environment. May also be used for protection of aluminium and concrete (special designed systems). Film thickness and spreading rate Minimum Maximum Typical Film thickness, dry mils (µm) 24,0(600) 40,0(1000) 30,0(750) Film thickness, wet mils (µm) 25,0(625) 42,0(1050) 31,2(780) Theoretical spreading rate ft²/gl (m²/l) 64(1,6) 38(0,96) 51(1,28) Comments The practical spreading rate may vary from the theoretical dependent upon film thickness and the ambient temperature, ventilation/wind during the application. Physical properties Color Red, White Solids (vol %)* 96 ± 2 Flash point 93°F ± 4 (34ºC ± 2) (Setaflash) VOC 36 gms/ltr UK-PG6/23(97). Appendix 3 Gloss Semiflat Water resistance Excellent Abrasion resistance Excellent Solvent resistance Excellent Chemical resistance Excellent Flexibility Limited *Measured according to ISO 3233:1998 (E) Surface preparation All surfaces should be clean, dry and free from contamination. The surface should be assessed and treated in accordance with ISO 8504. Bare steel Cleanliness: Blast cleaning to min. SSPC-SP10 "Near White Blast" or Sa 2 ½ (ISO 8501 1:2007). Roughness: use suitable abrasives to achieve Grade Coarse G 3 - 5 mils (75 - 130 µm, Ry5) (ISO 8503-2). Chemflake Special Page 1 of 5
Other surfaces The coating may be used on other substrates. Please contact your local Jotun office for more information. Condition during application The temperature of the substrate should be minimum 59°F (15°C) and at least 5°F (3°C) above the dew point of the air. The temperature and the relative humidity should be measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensure proper drying. The coating should not be exposed to oil, chemicals or mechanical stress until fully cured. Application methods Spray Use normal airless spray or two-comp. airless spray equipment Brush Recommended for stripe coating and small areas, care must be taken to achieve the specified dry film thickness. Chemflake Special Page 2 of 5
Page 1 and 2:
Painting Paul Wurth Paint System Ty
Page 3 and 4:
Carboline Benelux Braak 1 · 4704 R
Page 5 and 6:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 7 and 8:
PAINT SYSTEM Type C, PAINT MANUFACT
Page 9 and 10:
Page 11 and 12:
PAINT SYSTEM Type F, PAINT MANUFACT
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Selection & Specification Data Gene
Page 21 and 22:
.Selection & Specification Data . G
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Painting Paul Wurth Paint System Ty
Page 43 and 44:
Specification sheet Hempel (Germany
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
HEMPADUR FAST DRY 15560 SURFACE New
Page 61 and 62:
Product Data Issued: March 2009 Pag
Page 67 and 68: Product Data Issued: November 2008
Page 69 and 70: HEMPADUR MASTIC 45880/45881 Applica
Page 71 and 72: HEMPEL'S GALVOSIL 15702 SURFACE Rem
Page 73: HEMPEL’S SILICONE ALUMINIUM 56910
Page 77 and 78: HEMPADUR 85671 Issued January 2011
Page 79 and 80: HEMPADUR 85671 Microclimate: The ac
Page 81 and 82: HEMPADUR 85671 Issued January 2011
Page 83 and 84: Application Instructions Applicatio
Page 85 and 86: HEMPEL'S VINYL ESTER GF 35910 Issue
Page 87 and 88: Painting Paul Wurth Paint System Ty
Page 89 and 90: PAINT SYSTEM TYPE F * + TYPE J * PA
Page 91 and 92: E N G 0 3 0 5 Interseal 670HS S u r
Page 93 and 94: Interseal 670HS S u r f a c e T o l
Page 95 and 96: PRODUCT DESCRIPTION INTENDED USES P
Page 97 and 98: PRODUCT CHARACTERISTICS SYSTEMS COM
Page 99 and 100: Intertherm® 50 H i g h T e m p e r
Page 101 and 102: Intertherm ® 50 High Temperature S
Page 103 and 104: Painting Paul Wurth Paint System Ty
Page 105 and 106: Technical specification Customer: P
Page 115 and 116: Technical Data Barrier 80 Product d
Page 117: Typical paint system Barrier 80 1 x
Page 121 and 122: Drying time Drying times are genera
Page 123 and 124: Technical Data Penguard Express Pro
Page 125 and 126: Substrate temperature 40°C Surface
Page 127 and 128: Technical Data Epoxy HR Product des
Page 129 and 130: Typical paint system Epoxy HR 2 x 1
Page 131 and 132: Shopprimed steel Clean, dry and und
Page 133 and 134: Penguard FC Page 4 of 4
Page 135 and 136: Other surfaces The coating may be u
Page 137 and 138: ISSUED 6 DECEMBER 2007 BY JOTUN THI
Page 139 and 140: Condition during application The te
show all

English (United Kingdom) - Paul Wurth

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?