English (United Kingdom) - Paul Wurth

More documents

Recommendations

Info

PAINT SYSTEM FOR MAINTENANCE WORKS (on site) Cleaning before surface preparation Dedusting – Degreasing – Rinsing – Drying if necessary Surface preparation Abrasive Blast cleaning up to Sa 2 ½ grade Medium G on rust areas, picking off/sand papering on deteriorated but not rusted areas. Paint system Coat Nominal thickness en µm Trade name Description Colour 1 65 Carbozinc 11 Ethyl Zinc Silicate Green 2 40 Thermaline 4700 Silicone Finish Grey Total 105 or Thermaline 4000 Repair system Inorganic Silicate Cleaning before surface preparation Dedusting – Degreasing – Rinsing – Drying if necessary Surface preparation Abrasive Blast cleaning up to Sa 2 ½ grade Medium G on rust areas, picking off/sand papering on deteriorated but not rusted areas Paint system Coat Nominal thickness en µm Trade name Description Colour Touchup 65 Carbozinc 11 Ethyl Zinc Silicate Green 2 40 Thermaline 4700 or Silicone Finish Grey Thermaline 4000 Inorganic Silicate Total 105
Selection & Specification Data Generic Type Solvent Based Organic Zinc-Rich Epoxy Description Low VOC organic zinc epoxy steel primer with quick cure-to-topcoat characteristics for in-shop applications and quick turnaround requirements in the field. Carbozinc 858 has very good adhesion and undercutting resistance and is excellent for use as a corrosion resistant primer for a variety of applications. Features � Meets Class A slip co-efficient and creep testing criteria for use on faying surfaces � Meets SSPC Paint System 20 � Low temperature cure down to 35°F (2°C) � Protects against undercutting corrosion � Available in ASTM D520, Type II zinc version � May be applied with standard airless or conventional spray equipment � VOC compliant to current AIM regulations Color Green (0300) Finish Matte Primers Self Priming Topcoats Can be topcoated with Epoxies, Polyurethanes, Acrylics and others as recommended by your Carboline sales representative. Dry Film Thickness 3.0-5.0 mils (75-125 microns). Dry film thickness in excess of 8.0 mils (200 microns) per coat is not recommended. Solids Content* By Volume: 64% ± 2% Zinc Content By Weight: 81% ± 2% in dry film Theoretical Coverage Rate 1026 mil ft 2 (25.2 m 2 /l at 25 microns) 342 ft 2 at 3.0 mils (8.0 m 2 /l at 75 microns) Allow for loss in mixing and application VOC Values As Supplied: 2.5 lbs./gal (303 g/l) Thinned:* 8 oz/gal w/ #2: 2.8 lbs./gal (335 g/l) 8 oz/gal w/ #33: 2.82 lbs./gal (338 g/l) These are nominal values. *Use Thinner #76 for projects requiring nonphotochemically reactive solvents. Dry Temp. Resistance Continuous: 300°F (149°C) Non-Continuous: 350°F (177°C) May 2008 replaces August 2003 (Carbozinc 858) Carbozinc ® 858 (3-pack) Substrates & Surface Preparation General Surfaces must be clean and dry. Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating. Steel SSPC-SP6 with a 1.0-3.0 mil (25-75 micron) surface profile. SSPC-SP2 or SP3 for touch-up. Application Equipment Listed below are general equipment guidelines for the application of this product. Job site conditions may require modifications to these guidelines to achieve the desired results. General Guidelines: S p r a y Application (General) Conventional Spray The following spray equipment has been found suitable and is available from manufacturers such as Binks, DeVilbiss and Graco. Keep material under mild agitation during application. Agitated pressure pot equipped with dual regulators, 3/8” I.D. minimum material hose, .070” I.D. fluid tip and appropriate air cap. Airless Spray Pump Ratio: 30:1 (min.)* GPM Output: 3.0 (min.) Material Hose: 3/8” I.D. (min.) Tip Size: .017-.023” Output PSI: 2000-2200 Filter Size: 60 mesh *Teflon packings are recommended and available from the pump manufacturer. Brush For small areas and touch-up only. Use medium bristle brush and avoid rebrushing. Roller Not recommended To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE, EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Carbozinc® are registered trademarks of Carboline Company.
Page 1 and 2: Painting Paul Wurth Paint System Ty
Page 3 and 4: Carboline Benelux Braak 1 · 4704 R
Page 5 and 6: PAINT SYSTEM Type C, PAINT MANUFACT
Page 7 and 8: PAINT SYSTEM Type C, PAINT MANUFACT
Page 9 and 10: Carboline Benelux Braak 1 · 4704 R
Page 11 and 12: PAINT SYSTEM Type F, PAINT MANUFACT
Page 17: Carboline Benelux Braak 1 · 4704 R
Page 21 and 22: .Selection & Specification Data . G
Page 23 and 24: Selection & Specification Data Gene
Page 41 and 42: Painting Paul Wurth Paint System Ty
Page 43 and 44: Specification sheet Hempel (Germany
Page 59 and 60: HEMPADUR FAST DRY 15560 SURFACE New
Page 61 and 62: Product Data Issued: March 2009 Pag
Page 67 and 68: Product Data Issued: November 2008
Page 69 and 70:
HEMPADUR MASTIC 45880/45881 Applica
Page 71 and 72:
HEMPEL'S GALVOSIL 15702 SURFACE Rem
Page 73:
HEMPEL’S SILICONE ALUMINIUM 56910
Page 77 and 78:
HEMPADUR 85671 Issued January 2011
Page 79 and 80:
HEMPADUR 85671 Microclimate: The ac
Page 81 and 82:
HEMPADUR 85671 Issued January 2011
Page 83 and 84:
Application Instructions Applicatio
Page 85 and 86:
HEMPEL'S VINYL ESTER GF 35910 Issue
Page 87 and 88:
Painting Paul Wurth Paint System Ty
Page 89 and 90:
PAINT SYSTEM TYPE F * + TYPE J * PA
Page 91 and 92:
E N G 0 3 0 5 Interseal 670HS S u r
Page 93 and 94:
Interseal 670HS S u r f a c e T o l
Page 95 and 96:
PRODUCT DESCRIPTION INTENDED USES P
Page 97 and 98:
PRODUCT CHARACTERISTICS SYSTEMS COM
Page 99 and 100:
Intertherm® 50 H i g h T e m p e r
Page 101 and 102:
Intertherm ® 50 High Temperature S
Page 103 and 104:
Painting Paul Wurth Paint System Ty
Page 105 and 106:
Technical specification Customer: P
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Technical Data Barrier 80 Product d
Page 117 and 118:
Typical paint system Barrier 80 1 x
Page 119 and 120:
Other surfaces The coating may be u
Page 121 and 122:
Drying time Drying times are genera
Page 123 and 124:
Technical Data Penguard Express Pro
Page 125 and 126:
Substrate temperature 40°C Surface
Page 127 and 128:
Technical Data Epoxy HR Product des
Page 129 and 130:
Typical paint system Epoxy HR 2 x 1
Page 131 and 132:
Shopprimed steel Clean, dry and und
Page 133 and 134:
Penguard FC Page 4 of 4
Page 135 and 136:
Other surfaces The coating may be u
Page 137 and 138:
ISSUED 6 DECEMBER 2007 BY JOTUN THI
Page 139 and 140:
Condition during application The te
show all

English (United Kingdom) - Paul Wurth

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?