Geovision NVR Software Installation Guide - Use-IP

More documents

Recommendations

Info

2.12.6 In/Out Monitor 116 In the left menu, click In/Out Monitor. This page appears. Figure 2-61 � Input Status: Indicates the current status of the 16 inputs, whether it is On (triggered) or OFF (no input). � Output Status: Indicates the current status of the 16 outputs, whether it is ON (triggered) or Off (no output). Click ALL ON button to force all 16 outputs to be triggered. Click ALL OFF button to turn off all 16 outputs. Select the individual outputs to turn it ON to force the output to be triggered or turn it OFF. Click Submit button to save the changes, or click Cancel button to return the changes to its previous state.
2.12.7 Updating Firmware To update the firmware of GV-I/O Box: 1. In the left menu, click Firmware Update. This page appears. Figure 2-62 2. Click the Browse… button to open the firmware file (*.bin) 2 Hardware Accessories 3. Click the Upload button. This update procedure may take 60 seconds to complete. 4. When the Update is complete, a dialog box appears and asks you to reboot the system. 5. Click OK. GV-I/O Box starts the Reboot operation. Note: It is required to reboot GV-I/O Box after updating the firmware. Without rebooting, the firmware update is not complete. 117
Page 1 and 2:
Before attempting to connect or ope
Page 3 and 4:
Contents Important Notice before Us
Page 5 and 6:
Important Notice before Using GV-Vi
Page 7 and 8:
4. CPU Requirements: • For record
Page 9 and 10:
1.1 GV-4008 1 Video Capture Cards T
Page 11 and 12:
Connecting Hardware Watchdog 1 Vide
Page 13 and 14:
Troubleshooting Power Supply Issues
Page 15 and 16:
1 Video Capture Cards 6. To access
Page 17 and 18:
1.2 GV-3008 1 Video Capture Cards T
Page 19 and 20:
Connecting Two GV-3008 Cards 1 Vide
Page 21 and 22:
Specifications Interface PCI-E GV-3
Page 23 and 24:
Packing List (D-Type) 1. GV-Combo A
Page 25 and 26:
Connecting One GV-Combo A Card (DVI
Page 27 and 28:
Connecting Two GV-Combo A Cards 1 V
Page 29 and 30:
Specifications Interface Type PCI-E
Page 31 and 32:
Connecting One GV-1008 Card 1 Video
Page 33 and 34:
Figure 1-14 1 Video Capture Cards 2
Page 35 and 36:
1.5 GV-650A, GV-800A 1 Video Captur
Page 37 and 38:
1 Video Capture Cards For the BNC-t
Page 39 and 40:
Specifications Interface Type PCI,
Page 41 and 42:
Connecting One GV-600A Card 1 Video
Page 43 and 44:
Connecting Two GV-600A/GV-650A/GV-8
Page 45 and 46:
1.7 Installing Two Cards 1 Video Ca
Page 47 and 48:
Comparison Charts for Single-Card a
Page 49 and 50:
1.8 Installing Drivers 1 Video Capt
Page 51 and 52:
1.9 Connecting Hardware Watchdog 1
Page 53 and 54:
1 Video Capture Cards GV-3008 GV-30
Page 55 and 56:
Video Capture Cards GV-1008 GV-1120
Page 57 and 58:
1 Video Capture Cards GV-1008 x 2 G
Page 59 and 60:
2.1 GV-Multi Quad Card 2 Hardware A
Page 61 and 62:
Connections with Two Video Capture
Page 63 and 64:
2.2 GV-Loop Through Card 2 Hardware
Page 65 and 66:
Connections with Two Video Capture
Page 67 and 68:
RS-485 Device Connections 2 Hardwar
Page 69 and 70: 2.4 GV-NET/IO Card V3.1 2 Hardware
Page 71 and 72: 2 Hardware Accessories 4. Ensure to
Page 73 and 74: 2 Hardware Accessories 2. You can c
Page 75 and 76: 2 Hardware Accessories 2. You can c
Page 77 and 78: Extended Connections 2 Hardware Acc
Page 79 and 80: 2.5 GV-Hub V2 2 Hardware Accessorie
Page 81 and 82: Extending Transmission over the Dis
Page 83 and 84: 2.6 GV-COM V2 2 Hardware Accessorie
Page 85 and 86: Specifications Serial Interface USB
Page 87 and 88: Connections 2 Hardware Accessories
Page 89 and 90: 2.8 GV-I/O 12-Out Card V3 2 Hardwar
Page 91 and 92: Specifications Output DC IN DC 5V,
Page 93 and 94: Overview DIP Switch Figure 2-30 3 E
Page 95 and 96: Assigning Addresses to GV-I/O Box 1
Page 97 and 98: 2 Hardware Accessories 3. Multiple
Page 99 and 100: 2.10 GV-I/O Box (8 Ports) 2 Hardwar
Page 101 and 102: Connections There are three ways to
Page 103 and 104: Extending Transmission over the Dis
Page 105 and 106: Specifications Input Output Input 8
Page 107 and 108: Overview DIP Switch 1 ON To change
Page 109 and 110: Assigning Addresses to GV-I/O Box 4
Page 111 and 112: 2 Hardware Accessories 3. Multiple
Page 113 and 114: 2.12.1 Fixed IP Connection To assig
Page 115 and 116: 2 Hardware Accessories 2. In the Us
Page 117 and 118: 2.12.3 Other Setting In the left me
Page 119: 2.12.5 Output Setting In the left m
Page 123 and 124: 2.13 Installing USB Driver 2 Hardwa
Page 125 and 126: 3.1 Before You Start 3 Software Ins
Page 127 and 128: Installing the System To install th
Page 129 and 130: Third page: 21. Authentication Serv
Page 131 and 132: 4.1 Main System 4 Screen Overview 1
Page 133 and 134: 4.2 ViewLog 1 2 19 18 17 16 15 14 2
Page 135 and 136: Functional Panel The controls in th
Page 137 and 138: The controls in the RPB Client wind
Page 139 and 140: 4.5 MultiView Viewer 4 Screen Overv
Page 141 and 142: 4.6 Center V2 14 1 15 17 16 17 18 1
Page 143 and 144: 4.7 Control Center Toolbar The cont
Page 145 and 146: Troubleshooting GV-System is design
Page 147: Troubleshooting 143
show all

Geovision NVR Software Installation Guide - Use-IP

Create successful ePaper yourself

Delete template?

Save as template?