Geovision NVR Software Installation Guide - Use-IP

More documents

Recommendations

Info

Connecting One GV-3008 Card 14 • Connect the D-Type video and audio cables to the GV-3008 Card. • Connect the supplied Hardware Watchdog Jump Wire. For correct connection, see 1.9 Connecting Hardware Watchdog. • Connect the computer’s internal power supply to the GV-3008 Card. The Power LED should be lit in green and the card ready LED should also be lit in green to indicate the card is ready for use. Figure 1-7
Connecting Two GV-3008 Cards 1 Video Capture Cards You can install two GV-3008 Cards for a total of 16 channels. Master Card is the card with 1-8 channels and Slave Card is that with 9-16 channels. Normally, the card attached to the lower PCI slot number will act as Master, and the card attached to the higher PCI slot number will act as Slave. • Hardware Watchdog Connection: Connect the supplied Hardware Watchdog Jump Wire to the Master Card. For correct connection, see 1.9 Connecting Hardware Watchdog. • Accessory Card Connections: � GV-NET/IO Card: Connect the card only to the Master Card. � GV-Loop Through Card: Connect one card for each video capture card. � GV-Multi Quad Card: Connect one card to any of two video capture cards. Figure 1-8 15
Page 1 and 2: Before attempting to connect or ope
Page 3 and 4: Contents Important Notice before Us
Page 5 and 6: Important Notice before Using GV-Vi
Page 7 and 8: 4. CPU Requirements: • For record
Page 9 and 10: 1.1 GV-4008 1 Video Capture Cards T
Page 11 and 12: Connecting Hardware Watchdog 1 Vide
Page 13 and 14: Troubleshooting Power Supply Issues
Page 15 and 16: 1 Video Capture Cards 6. To access
Page 17: 1.2 GV-3008 1 Video Capture Cards T
Page 21 and 22: Specifications Interface PCI-E GV-3
Page 23 and 24: Packing List (D-Type) 1. GV-Combo A
Page 25 and 26: Connecting One GV-Combo A Card (DVI
Page 27 and 28: Connecting Two GV-Combo A Cards 1 V
Page 29 and 30: Specifications Interface Type PCI-E
Page 31 and 32: Connecting One GV-1008 Card 1 Video
Page 33 and 34: Figure 1-14 1 Video Capture Cards 2
Page 35 and 36: 1.5 GV-650A, GV-800A 1 Video Captur
Page 37 and 38: 1 Video Capture Cards For the BNC-t
Page 39 and 40: Specifications Interface Type PCI,
Page 41 and 42: Connecting One GV-600A Card 1 Video
Page 43 and 44: Connecting Two GV-600A/GV-650A/GV-8
Page 45 and 46: 1.7 Installing Two Cards 1 Video Ca
Page 47 and 48: Comparison Charts for Single-Card a
Page 49 and 50: 1.8 Installing Drivers 1 Video Capt
Page 51 and 52: 1.9 Connecting Hardware Watchdog 1
Page 53 and 54: 1 Video Capture Cards GV-3008 GV-30
Page 55 and 56: Video Capture Cards GV-1008 GV-1120
Page 57 and 58: 1 Video Capture Cards GV-1008 x 2 G
Page 59 and 60: 2.1 GV-Multi Quad Card 2 Hardware A
Page 61 and 62: Connections with Two Video Capture
Page 63 and 64: 2.2 GV-Loop Through Card 2 Hardware
Page 65 and 66: Connections with Two Video Capture
Page 67 and 68: RS-485 Device Connections 2 Hardwar
Page 69 and 70:
2.4 GV-NET/IO Card V3.1 2 Hardware
Page 71 and 72:
2 Hardware Accessories 4. Ensure to
Page 73 and 74:
2 Hardware Accessories 2. You can c
Page 75 and 76:
2 Hardware Accessories 2. You can c
Page 77 and 78:
Extended Connections 2 Hardware Acc
Page 79 and 80:
2.5 GV-Hub V2 2 Hardware Accessorie
Page 81 and 82:
Extending Transmission over the Dis
Page 83 and 84:
2.6 GV-COM V2 2 Hardware Accessorie
Page 85 and 86:
Specifications Serial Interface USB
Page 87 and 88:
Connections 2 Hardware Accessories
Page 89 and 90:
2.8 GV-I/O 12-Out Card V3 2 Hardwar
Page 91 and 92:
Specifications Output DC IN DC 5V,
Page 93 and 94:
Overview DIP Switch Figure 2-30 3 E
Page 95 and 96:
Assigning Addresses to GV-I/O Box 1
Page 97 and 98:
2 Hardware Accessories 3. Multiple
Page 99 and 100:
2.10 GV-I/O Box (8 Ports) 2 Hardwar
Page 101 and 102:
Connections There are three ways to
Page 103 and 104:
Extending Transmission over the Dis
Page 105 and 106:
Specifications Input Output Input 8
Page 107 and 108:
Overview DIP Switch 1 ON To change
Page 109 and 110:
Assigning Addresses to GV-I/O Box 4
Page 111 and 112:
2 Hardware Accessories 3. Multiple
Page 113 and 114:
2.12.1 Fixed IP Connection To assig
Page 115 and 116:
2 Hardware Accessories 2. In the Us
Page 117 and 118:
2.12.3 Other Setting In the left me
Page 119 and 120:
2.12.5 Output Setting In the left m
Page 121 and 122:
2.12.7 Updating Firmware To update
Page 123 and 124:
2.13 Installing USB Driver 2 Hardwa
Page 125 and 126:
3.1 Before You Start 3 Software Ins
Page 127 and 128:
Installing the System To install th
Page 129 and 130:
Third page: 21. Authentication Serv
Page 131 and 132:
4.1 Main System 4 Screen Overview 1
Page 133 and 134:
4.2 ViewLog 1 2 19 18 17 16 15 14 2
Page 135 and 136:
Functional Panel The controls in th
Page 137 and 138:
The controls in the RPB Client wind
Page 139 and 140:
4.5 MultiView Viewer 4 Screen Overv
Page 141 and 142:
4.6 Center V2 14 1 15 17 16 17 18 1
Page 143 and 144:
4.7 Control Center Toolbar The cont
Page 145 and 146:
Troubleshooting GV-System is design
Page 147:
Troubleshooting 143
show all

Geovision NVR Software Installation Guide - Use-IP

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?