roweld cnc s4 - Rothenberger
roweld cnc s4 - Rothenberger
roweld cnc s4 - Rothenberger
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Machine type:<br />
Select machine type in line 4. Use the main selector keys (from bottom to top). A subwindow<br />
opens whenever the machine type is changed (see DATALINE 3.1.2.1). If an identification<br />
number has not been entered for the selected machine type, a subwindow opens automatically.<br />
Language:<br />
Select menue language in line 5 with main selector keys. If the default is change, confirm choice<br />
with ENTER. The selected language is loaded automatically. The cursor returns to upper<br />
position.<br />
Date:<br />
Enter current date in line 6 with numerical character keys. Observe the following format:<br />
DD.MM.YYYY (e. g. 01.01.2001 for January 1, 2001). Correct or remove entry with delete key<br />
(DEL). The old date can be overwritten; the line is deleted with the entry of the first numerical<br />
character.<br />
Time:<br />
Set the time in line 7. Observe the following format: HH:MM:SS (24h format, i.e. 12:34:56 =<br />
12:34:56 pm). Press ENTER to immediate time settings immediately.<br />
If the Default menue is invoked automatically, the main menue appears. Otherwise the system<br />
asks for a password to access other Default submenues (DATALINE 3.1.3). If you enter an<br />
incorrect password, the system automatically returns to the main menue or the systems repeats<br />
password query. Remember to confirm each line/entry with ENTER.<br />
CNC:<br />
Activate the CNC functionality of the DATALINE data logger in line 8. Change selection with<br />
main selector keys.<br />
For additional default options, confer ROWELD DATLINE operating instructions.<br />
The pressure sensor setting (DATALINE 3.1.3.1) are of no significance in CNC mode. The pressure<br />
defaults are read from the control unit. Solely the offset settings are effective.<br />
4.1.3 Set up – inserting pipes<br />
If only the operator control unit is switched or the DATALINE data logger is in the main menue<br />
or in the Default menue, the basic unit can be opened and closed with the joystick. The opening<br />
and closing movements are in slow-motion. If both the joystick and the OK button are actuated,<br />
the basic unit opens and closes in rapid-motion. If the opening/closing speed exceeds 10<br />
mm/sec., the OK button flashes.<br />
Fully open the basic unit to insert pipes. If the diameter of the pipes is less than the maximum<br />
permissible diameter, mount the adapter clamping inserts (consisting of six wide-surface shells<br />
and two small-surface shells) to clamps and tighten with the Allen key. Pease observe that the<br />
small-surface shells are mounted to the two lower external main clamps. These shells may only<br />
be mounted to the upper left main clamps when making pipe-to-pipe bend joints.<br />
Insert the plastic pipe or fitting in the clamping device (use dolly with longer pipe sections) and<br />
tighten brass nut on the upper clamps. Adjust brass nuts (tighten or loosen) to compensate for<br />
any ovalness.<br />
For semi-automatic welding machine only:<br />
Pipe-to-pipe joints: snap spacers into the two left clamps; pipe-to-fitting joints: snap spacers into<br />
the two centre clamps so that the pipe section held by 3 clamps and the fitting by 1 clamp. The<br />
third main clamp can be positioned on the rod as required to securely clamp and weld the<br />
pieces.<br />
ENGLISH<br />
25