Register and win! B 140 R - Megaobrabiarki

Start upBatteriesPlease observe the following warning noteswhen handling batteries:Observe the directions on the battery,in the instructions for use andin the vehicle operating instructionsWear eye protectionKeep children away from acid andbatteriesDanger of explosionFire, sparks, naked flames andsmoking must be strictly avoidedDanger of chemical burnsFirst aidWarning noteDisposalDo not throw the battery into theregular waste DangerDanger of explosion. Do not put tools orsimilar on the battery, i.e. on the terminalpoles and cell connectors.Risk of injury. Ensure that wounds never comeinto contact with lead. Always clean your handsafter having worked with batteries.Insert batteries and connectThe BP package model contains a built-inbattery. Tilt the water tank backwards. Insert the battery in the trough. WarningPay attention to correct poles. Connect the connection cable to thefree battery poles (+) and (-). Tilt the water tank towards the front. WarningCharge the battery before commissioningthe machine.Charging batteryNoteThe device is equipped with a safety mechanismto prevent total discharge, i.e. whenthe permissible minimum capacity isreached, then the machine can only bedriven and existing lamps can be switchedon. In such a case, the battery monitoringsymbol on the control console glows red. Drive the machine directly to the chargingstation; avoid any steep gradients inthe process.NoteWhile using other batteries (for e.g. batteriesfrom other manufacturers) the total dischargeprotection level must be reset bythe Kärcher aftersales service according tothe respective battery. DangerRisk of electric shock. Observe supply networkand fuse protection - see "Charger".Only use the charger in dry rooms with sufficientventilation!NoteAverage charging time is approx. 10 hours.The recommended chargers (matching thebatteries used) are regulated electronicallyand will automatically switch off the chargingprocess. DangerDanger of explosion. Wet batteries canonly be charged with opened hood. Empty the dirt water reservoir. Tilt the dirt water tank backwards. Remove battery plug and join it to thecharging cable. Connect the charger to the mains andturn it on.After charging Switch off the charger and remove theplug from the socket. Pull the battery cable from the chargercable and connect it to the machine.Low maintenance batteries (wet batteries) Add distilled water one hour before thecharging process comes to an end; followthe correct acid level. There arecorresponding indicators on the battery.At the end of the charging process, allcells must gas. DangerDanger of causticization!– Adding water to the battery in its dischargedstate can cause the acid toleak.– Use safety glasses while handling batteryacid and follow the safety instructionsto avoid personal injury or damageto clothes.– Should the acid spray on to the skin orclothes, rinse immediately with lots ofwater. WarningRisk of damage!– Use only distilled or desalinated water(EN 50272-T3) for filling the battery.– Do not add any substances (so-calledperformance improving agents), elsewarranty claims will not be entertained.Recommended batteriesBattery setOrder No.400 Ah, wet batteries 6.654-052.0240 Ah, wet batteries 6.654-112.0Recommended chargersChargerOrder No.400 Ah 6.654-139.0240 Ah 6.654-193.0Batteries and chargers are available in specialisedstores.Recommended accessoriesStorage system to refill wet batteries.– With wall mount, order no.: 2.641-234.0– Without wall mount, order no.: 2.641-244.0Maximum battery dimensionsLength Width Height620 mm 430 mm 467 mmIf you use wet batteries in the Bp model,then follow the following instructions:– It is necessary to conform to the maximumbattery dimensions.– While charging wet (maintenance-free)batteries, it is necessary to tilt the seat upward.– While charging wet batteries, follow thespecifications of the battery manufacturer.Remove the battery Tilt the water tank backwards. Disconnect batteries. Remove the battery from the pan. Tilt the water tank towards the front.UnloadingNotePull the red battery plug to put all functionsout of operation immediately. Remove the packaging film. Remove the elastic tape fasteners atthe stop points. Three indicated floor boards of the palletare fastened with screws. Unscrewthese boards. Place the boards on the edge of the pallet.Place the boards in such a way thatthey lie in front of the four wheels of themachine. Fasten the boards withscrews.EN - 421