11 PRE-SELECTION EXAMPLE11ESEMPIO PER PRESELEZIONEa) Given parametersTransmitted powerInput speedOutput speedDrive ratioP = 0,16 Kwn1 = 36 g/1’n2 = 10,75 g/1’i = n1 = 3,35n1a) Parametri datiPotenza trasmessa P = 0,16 KwVelocità in entrata n1 = 36 g/1’Velocità in uscita n2 = 10,75 g/1’Rapporto di trasmissione i = n1 = 3,35n1Driving mechanism = electric motor with reduction gear unit.Driven mechanism = belt conveyor with uneven loadsFactor (according table 2) = 1,4Center distance at = 530 mmMax. chain width = 25 mmTeeth number Z1 = 17; Z2 = i • Z1 = 57Factor assigned considering the number of teethof ƒ2 sprocket = 1,55 (see picture no. 1)b) Chain pre-selectionPower, following the base equation (item3)Pc = P • ƒ1 • ƒ2 (Kw)Pc = 0,16 • 1,4 • 1,55 = 0,35 KwThus following picture 2for Pc= 0,35 Kw and n1 = 36 R.P.M.,the roller chain type 126 (ISO 08B-1)or A40 (ISO 08A-1) p = 12,70 mm is selectedc) Chain SpeedV = n • z • p m/sec60.000V =36 • 17 • 12,70 = 0,13 m/sec60.000d) LubricationFor V=0,13 m/sec with chain type 126 (ISO 08B-1) according topicture 4, = field 1 and thus: oil applied manually with brush or oilerat frequent interval.Macchina conduttrice = motore elettrico con riduttore a ingranaggi.Macchina condotta = trasportatore a tappeto, con carichi non uniformi.Fattore ƒ1 (secondo tab. 2) = 1,4Interasse a = 530 mmMassima larghezza catena = 25 mmNumero di denti Z1 = 17; Z2 = i • Z1 = 57Fattore ƒ2 assegnato in base al numero di denti del pignoneƒ2 = 1,55 (secondo fig. 1)b) Preselezione della catenaPotenza, secondo l’equazione base (punto 3)Pc = P • ƒ1 • ƒ2 (Kw)Pc = 0,16 • 1,4 • 1,55 = 0,35 KwCon questo, viene scelta da fig. 2per Pc = 0,35 Kw e n1 = 36 g/1’,la catena a rulli tipo 126 (ISO 08B-1)oppure A40 (ISO 08A-1) p = 12,70 mm.c) Velocità della catenaV = n • z • p m/sec60.000V =36 • 17 • 12,70 = 0,13 m/sec60.000d) Lubrificazioneper V=0,13 m/sec. con catena 126 (ISO 08B-1) secondo la fig. 4,= campo 1 e quindi: olio applicato manualmente con pennello ooliatore ad intervalli frequenti.136
e) Chain length:The number of pitches can be determined as follows.Xo = 2 • ao + Z1 + Z2 + ƒ3 • pp 2 aoƒ3 according to table 6Xo = 2 • 530 + 17 + 57 40,529 • 12,70+12,70 2 530with ƒ3 = 40,529 per Z2 - Z1 = 57 -17 = 40e) Lunghezza catenaIl numero di maglie può essere determinato come segue:Xo = 2 • ao + Z1 + Z2 + ƒ3 • pp 2 aoƒ3 secondo la tab. 6Xo = 2 • 530 + 17 + 57 40,529 • 12,70+12,70 2 530con ƒ3 = 40,529 per Z2 - Z1 = 57 -17 = 40Xo = 121,44select X = 122 linksXo = 121,44scegliere X = 122 maglief) Center distanceThe center distance can be determined as follows:a = [ 2X - (Z1 + Z2) ] • ƒ4 • pƒ4 according to table 7A = [ 2 • 122 – (17+57) ] • 0,24715 • 12,70X - Z1con ƒ4 = 0,24715 per = 122-17 = 2,625(interpolated)Z2 - Z1 57-17A = 533,6 mm.f) InterasseL’interasse può essere determinato come segue:a = [ 2X - (Z1 + Z2) ] • ƒ4 • pƒ4 vedi tab. 7A = [ 2 • 122 – (17+57) ] • 0,24715 • 12,70X - Z1con ƒ4 = 0,24715 per = 122-17 = 2,625(interpolato)Z2 - Z1 57-17A = 533,6 mm.137