ICR 803 Bar Code Scanner BAR CODE MANUAL

More documents

Recommendations

Info

Using This Manual This manual contains bar codes used to program the ICR803. For initial setup, product identification, and general product information, please refer to the following manuals: ICR803 Quick Start Manual ICR803 Command & Communication Guide Plug and Play Bar Codes Plug and Play bar codes provide instant engine set up for commonly used interfaces. Please note that the ICR803 interfaces are configured by the factory at time of order. These bar codes are therefore used to default the scanner to get back to the factory setup. RS-232 The RS-232 Interface bar code is used when connecting to the serial port of a PC or terminal. The following RS-232 Interface bar code also programs a carriage return (CR) and a line feed (LF) suffix, baud rate, and data format as indicated below: USB HID Option Setting Baud Rate 115200 bps Data Format 8 data bits, no parity bit, 1 stop bit RS-232 Interface Scan the following code to default the USB version of the ICR803 for USB HID bar code imagers. Scanning this code changes the terminal ID to 131. USB HID Bar Code Imager ICR803 Bar Code Manual – Rev A – 04/2007 - 2 -
USB COM Port Emulation Scan the following code to program the USB version of the ICR803 to emulate a regular RS-232 based COM port. If you are using Microsoft Windows, you will need to install the USB Driver for the scanner. ICR803 Bar Code Manual – Rev A – 04/2007 - 3 -
Page 1: ICR 803 Bar Code Scanner BAR CODE M
Page 5 and 6: ICR803 Bar Code Manual - Rev A - 04
Page 7 and 8: Good Read Indicators ICR803 Bar Cod
Page 9 and 10: Reread Delay This sets the minimum
Page 11 and 12: Manual Trigger, Low Power The image
Page 13 and 14: LED Power Level This selection allo
Page 15 and 16: Centering Use Centering to narrow t
Page 17 and 18: Decode Search Mode There are three
Page 19 and 20: Output Sequence Example In this exa
Page 21 and 22: Multiple Symbols No Read Note: This
Page 23 and 24: - 23 -
Page 25 and 26: To add a backslash (\), scan 5, C,
Page 27 and 28: Intercharacter, Interfunction, and
Page 29 and 30: Data Formatting Data Format Editor
Page 31 and 32: count of the number of suppressed c
Page 33 and 34: Symbologies This programming sectio
Page 35 and 36: - 35 -
Page 37 and 38: Codabar Message Length Scan the bar
Page 39 and 40: Code 39 Message Length Scan the bar
Page 41 and 42: FULL ASCII Full ASCII Code 39 decod
Page 43 and 44: Interleaved 2 of 5 Message Length S
Page 45 and 46: Code 2 of 5 Code 2 of 5 Message Len
Page 47 and 48: Matrix 2 of 5 Matrix 2 of 5 Message
Page 49 and 50: Code 128 ISBT 128 Concatenation In
Page 51 and 52: Telepen Telepen Output Using AIM Te
Page 53 and 54:
UPC-A Addenda This selection adds 2
Page 55 and 56:
UPC-E0 Addenda Required When Addend
Page 57 and 58:
- 57 -
Page 59 and 60:
- 59 -
Page 61 and 62:
- 61 -
Page 63 and 64:
- 63 -
Page 65 and 66:
Code 49 Message Length Scan the bar
Page 67 and 68:
MicroPDF417 - 67 -
Page 69 and 70:
EAN•UCC Emulation The imager can
Page 71 and 72:
- 71 -
Page 73 and 74:
Korea Post Korea Post Message Lengt
Page 75 and 76:
Data Matrix Data Matrix Message Len
Page 77 and 78:
Aztec Code Aztec Code Message Lengt
Page 79 and 80:
OCR Default All OCR Settings turns
Page 81 and 82:
Creating OCR Templates You can crea
Page 83 and 84:
9902XZ50 You can string together as
Page 85 and 86:
OCR Modulo 36 Character Set Scan th
Page 87 and 88:
Test Menu When you scan the Test Me
Page 89 and 90:
Plessey Code ]P0 n (0x6E) PosiCode
Page 91 and 92:
APPENDIX C - Sample Symbols - 91 -
Page 93 and 94:
APPENDIX D - Programming Charts - 9
Page 95 and 96:
APPENDIX D - Programming Charts - 9
show all

ICR 803 Bar Code Scanner BAR CODE MANUAL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?