05.08.2013 Views

Trouble Godes - diagramas.diagram...

Trouble Godes - diagramas.diagram...

Trouble Godes - diagramas.diagram...

SHOW MORE
SHOW LESS

You also want an ePaper? Increase the reach of your titles

YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.

Model: Almera l,S/l,8 Almera Tino 1,8 Primera l,6/l,8/2,O<br />

X-Trail 2,012,s Navara Pick-up 2,4 NISSAN<br />

0 The fourth group of flashes indicate the 'units' of the trouble<br />

code KI [Dl.<br />

0 Ten flashes in a group indicate '0'.<br />

o A short pause separates each trouble code group KI [El.<br />

0 A long pause separates each trouble code [F].<br />

o For example: <strong>Trouble</strong> code PI130 displayed O.<br />

Switch ignition OFF.<br />

<strong>Trouble</strong> code identification<br />

Flash type EOBD type Fault location<br />

-<br />

0011<br />

0021<br />

0031<br />

0032<br />

0037<br />

0038<br />

0051<br />

0052<br />

0057<br />

0058<br />

0101<br />

PO<br />

-<br />

-<br />

-<br />

-<br />

-<br />

-<br />

-<br />

-<br />

-<br />

-<br />

-<br />

Refer to EOBD trouble code tabte<br />

Camshaft position control system -<br />

bank 1 - performance problem<br />

Camshaft position control system -<br />

bank 2 - performance probtem<br />

Heated oxygen sensor (H02S) 1,<br />

bank 1 - heater voltage low<br />

Heated oxygen sensor (H02S) 1,<br />

bank 1 - heater voltage high<br />

Heated oxygen sensor (H02S) 2,<br />

bank 1 - heater voltage low<br />

Heated oxygen sensor (H02S) 2,<br />

bank 1 - heater voltage high<br />

Heated oxygen sensor (H02S) 1,<br />

bank 2 - heater voltage low<br />

Heated oxygen sensor (H02S) 1,<br />

bank 2 - heater voltage high<br />

Heated oxygen sensor (H02S) 2,<br />

bank 2 - heater voltage low<br />

Heated oxygen sensor (H02S) 2,<br />

bank 2 - heater voltage high<br />

Mass air flow (MAF) sensor -<br />

rangelperformance problem<br />

I low<br />

Engine managementltransmission<br />

'; i, v<br />

I -<br />

Erasing<br />

Ensure accelerator pedal is fully released.<br />

Ensure ignition switched OFF for at least 10 seconds.<br />

Switch ignition ON. DO NOT start engine.<br />

Wait 3 seconds.<br />

Within 5 seconds, repeat the following 5 times:<br />

o Fully depress accelerator pedal.<br />

0 Fully release accelerator ~edal.<br />

~aii 7 seconds.<br />

Fully depress accelerator pedal.<br />

After approximately 10 seconds MIL will start flashing.<br />

Fully release accelerator pedal.<br />

<strong>Trouble</strong> codes are now displayed by MIL.<br />

Fully depress accelerator pedal for more than 10 seconds<br />

Fully release accelerator pedal.<br />

<strong>Trouble</strong> code 0000 should be displayed.<br />

-<br />

Probable cause<br />

0102 l - Mass air flow (MAF) sensor - voltage Wiring, MAF sensor, air leak, ECM<br />

-<br />

Wiring, CMP sensor, CKP sensor, valve timing<br />

sensor<br />

Wiring, CMP sensor, CKP sensor, valve timing<br />

sensor<br />

Wiring, H02S heater, ECM<br />

Wiring, H02S heater, ECM<br />

Wiring, H02S heater, ECM<br />

Wiring, H02S heater, ECM<br />

Wiring, H02S heater, ECM<br />

Wiring, H02S heater, ECM<br />

Wiring, H02S heater, ECM<br />

Wiring, H02S heater, ECM<br />

Wiring, MAF sensor, air leak, ECM

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!