05.08.2013 Views

Trouble Godes - diagramas.diagram...

Trouble Godes - diagramas.diagram...

Trouble Godes - diagramas.diagram...

SHOW MORE
SHOW LESS

Create successful ePaper yourself

Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.

I Engine management<br />

Flash type<br />

4-digit<br />

2341<br />

2342<br />

2413<br />

4444<br />

Fault location<br />

Heated oxygen sensor (H02S) - lambda<br />

control<br />

Heated oxygen sensor (H02S)<br />

Mixture control (MC)<br />

No fault found<br />

Model: Favorit 1,3 Favorit VanlForman Pick-up 1,3 Felicia 1,3<br />

Probable cause<br />

rn <strong>Trouble</strong> code may be displayed if engine is not idling during self-diagnosis due to missing CKP sensor signal. lgnore trouble code if<br />

engine starts.<br />

After repairs, erase learnt lambda control values: Wait 30 seconds. Disconnect battery or ECM multi-plug for at least 30 seconds.<br />

Carry out road test to allow ECM to re-learn basic values.<br />

type<br />

5-digit<br />

00000<br />

FauH location<br />

No fault found<br />

Heating inoperative, exhaust leak, misfire, fuel pressurelpump,<br />

EVAP canister purge valve<br />

Wiring, H02S, heating inoperative, fuel level low<br />

Fuel level low, fuel pressurelpump, intakelexhaust leak, misfire,<br />

H02S, EVAP canister purge valve, injector, excessive fuel in<br />

engine oil<br />

00282 I Idle speed control (ISC) actuator I Wiring, multi-plug incorrectly wired, ISC actuator<br />

-<br />

Probable cause<br />

-<br />

0051 5 Crankshaft position (CKP) sensor<br />

Insecure rotor, wiring, CKP sensor<br />

0051 6 Closed throttle position (CTP) switch Accelerator cable adjustment, CTP switch adjustment, wiring,<br />

CTP switch<br />

0051 8 / Throttle position (TP) sensor 1 Wiring, poor connection, TP sensor<br />

00522 Engine coolant temperature (ECT) sensor Wiring, poor connection, ECT sensor<br />

00523 Intake air temperature (IAT) sensor Wiring, IAT sensor<br />

00525 Heated oxygen sensor (H02S)<br />

Wiring, H02S, heating inoperative, fuel level low<br />

00537 Heated oxygen sensor (H02S) -<br />

lambda control<br />

Heating inoperative, exhaust leak, misfire, fuel pressurelpump,<br />

EVAP canister purge valve<br />

00561 Mixture control (MC)<br />

Fuel level low, fuel pressurelpump, intakelexhaust leak, misfire,<br />

H02S, EVAP canister purge valve, injector, excessive fuel in<br />

65535 I Engine mntrol module (ECM)<br />

enaine oil<br />

Wiring, ECM<br />

rn <strong>Trouble</strong> code may be displayed if engine is not idling during self-diagnosis due to missing CKP sensor signal. Ignore trouble code if<br />

engine starts.<br />

After repairs, erase learnt lambda control values as follows:<br />

FavoritlForman: Wait 30 seconds. Disconnect battery or ECM multi-plug for at least 30 seconds.<br />

Felicia: Erase using diagnostic equipment.<br />

Carry out road test to allow ECM to re-learn basic values. 4

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!