- Page 2 and 3: Disclaimer Welch Allyn ® reserves
- Page 4 and 5: The CE mark on the product indicate
- Page 6 and 7: Section 3 Tailoring the Interface (
- Page 8 and 9: Section 5 Building the Message Stri
- Page 10 and 11: Section 7 Symbologies (continued) S
- Page 13 and 14: VALUETEAM 3060 or 3080 Hand held CC
- Page 15 and 16: Reading Width VT3060 60mm 2.3” VT
- Page 17 and 18: Disconnect power to your terminal/c
- Page 19: To program each option, you must: 1
- Page 23: Enter Programming Terminal St
- Page 27 and 28: Output Style . . . . . . . . . . .
- Page 29 and 30: Enter Programming Output Styl
- Page 31: Enter Programming Keyboard La
- Page 34 and 35: 3 Word Length/Parity:
- Page 36 and 37: 3 Baud Rate:
- Page 38 and 39: 3 Time Out Control: This allows
- Page 40 and 41: 3 Output Polarity . . .
- Page 42 and 43: 3 Output Polarity: Wand Emulati
- Page 44 and 45: 3 Module Time: This selection p
- Page 47: The Scanner Set Up selections allow
- Page 50 and 51: 4 Beeper Tone: This selection
- Page 52 and 53: 4 Trigger Mode Manual Trigger,
- Page 54 and 55: 4 Low Power Trigger Delay: Whe
- Page 56 and 57: 4 Reread Delay: This selection
- Page 59 and 60: When a bar code is scanned, additio
- Page 61 and 62: Prefix . . . . . . . . . . . . . .
- Page 63 and 64: Enter Programming Prefix Suff
- Page 65 and 66: Hex to ASCII Conversion Chart
- Page 67 and 68: Enter Programming Intercharacter De
- Page 69 and 70: STX . . . . . . . . . . . . . . . .
- Page 71 and 72:
Enter Programming STX/ETX Rec
- Page 73 and 74:
Enter Programming Prefix/Suffix Cod
- Page 75:
Enter Programming Prefix/Suff
- Page 79 and 80:
Editor Control . . . . . . . . . .
- Page 81 and 82:
Enter Programming Editor Control
- Page 83:
Enter Programming Symbology Control
- Page 86 and 87:
7 The 3060/3080 scanner is prese
- Page 88 and 89:
7 Standard Code 39: The standar
- Page 90 and 91:
7 Code 39 Minimum and Maximum L
- Page 93 and 94:
Standard Codabar: The standard Coda
- Page 95 and 96:
Enter Programming Codabar Se
- Page 97 and 98:
Enter Programming Codabar Mi
- Page 99 and 100:
Enter Programming UPC Select
- Page 101 and 102:
Enter Programming EAN/CAN/JA
- Page 103 and 104:
Enter Programming Code 2
- Page 105 and 106:
Enter Programming Code 2
- Page 107 and 108:
Enter Programming IATA Selec
- Page 109 and 110:
Enter Programming Code 11 C
- Page 111 and 112:
Enter Programming Code 93 C
- Page 113 and 114:
Enter Programming MSI/Plesse
- Page 115 and 116:
Enter Programming UK/Plessey
- Page 117:
Enter Programming UCC/EAN-12
- Page 120 and 121:
8 In the United States, please cont
- Page 122 and 123:
8 Welch Allyn, Inc., hereby warra
- Page 125 and 126:
The Appendix lists the beeping indi
- Page 127 and 128:
The Keyboard Function Code Table is
- Page 130:
A B C D E F 0 (YES) 1 (NO) 2