Untitled

More documents

Recommendations

Info

2 To program the scanner for your terminal/computer: Scan the Enter Programming bar code at the top of page 2 - 3. Scan the Terminal bar code to enter the option mode. Scan the appropriate two digit alphanumeric entry code from the chart on the fold out back cover of this manual. Scan the Exit Programming bar code at the bottom of page 2 - 3. If you program a different Terminal Selection, and later wish to reset the scanner to the defaulted terminal, scan the Default Terminal bar code below. This will reset the scanner to the default terminal, noted on page 2 - 3 by an asterisk (✱) beside each terminal type. Default Terminal
Enter Programming Terminal Standard/TTL RS-232 peer to peer interface . . . . . . . . . . . . . . . . . . . . 00 IBM PC/XT, 286/XT keyboard wedge . . . . . . . . . . . . . . . . . . . . . . . . . . . 01 IBM PS/2 25 - 30 series keyboard wedge . . . . . . . . . . . . . . . . . . . . . . . 02 IBM PC/AT, PS/1, PS/VP, series keyboard wedge ✱ . . . . . . . . . . . . . . 03 IBM PS/2 30 (286), 35 - 120 series keyboard wedge ✱ . . . . . . . . . . . 03 COMPAQ 386/486 series keyboard wedge ✱ . . . . . . . . . . . . . . . . . . . 03 HP Vectra series PC keyboard wedge ✱ . . . . . . . . . . . . . . . . . . . . . . . . General Notebook PC keyboard wedge 03 (PC/AT, PS/2 Compatibles) ✱ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03 APPLE ADB keyboard wedge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Wand emulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Serial Wedge (RS–232) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 OCIA (special order model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Exit Programming 2
Page 2 and 3: Disclaimer Welch Allyn ® reserves
Page 4 and 5: The CE mark on the product indicate
Page 6 and 7: Section 3 Tailoring the Interface (
Page 8 and 9: Section 5 Building the Message Stri
Page 10 and 11: Section 7 Symbologies (continued) S
Page 13 and 14: VALUETEAM 3060 or 3080 Hand held CC
Page 15 and 16: Reading Width VT3060 60mm 2.3” VT
Page 17 and 18: Disconnect power to your terminal/c
Page 19: To program each option, you must: 1
Page 25: Once you have programmed your Termi
Page 28 and 29: 3 Output Style: Regular is used
Page 30 and 31: 3 Keyboard Layout: This selecti
Page 33 and 34: Word Length/Parity . . . . . . . .
Page 35 and 36: Enter Programming Word Length/
Page 37 and 38: Enter Programming Baud Rate Ha
Page 39 and 40: Enter Programming Time Out Con
Page 41 and 42: Initial signal state Margin time Ex
Page 43 and 44: Enter Programming Output Pola
Page 45: Enter Programming Module Time
Page 49 and 50: Beeper Tone . . . . . . . . . . . .
Page 51 and 52: Enter Programming Beeper Ton
Page 53 and 54: Enter Programming Trigger Mo
Page 55 and 56: Enter Programming Low Power
Page 57: Enter Programming Reread Del
Page 60 and 61: 5 The following diagram illu
Page 62 and 63: 5 Prefix: Prefix Prefix Code ID
Page 64 and 65: 5 Example: Add a prefix or suff
Page 66 and 67: 5 Some terminals drop informati
Page 68 and 69: 5 The following diagram illus
Page 70 and 71: 5 STX/ETX: STX Prefix Code ID S
Page 72 and 73:
5 Prefix and Suffix Code ID: P
Page 74 and 75:
5 Prefix/Suffix Code ID Bar Co
Page 77:
The Data Editor selections are used
Page 80 and 81:
6 The Data Editor is used to ed
Page 82 and 83:
6 The Data Editor Control chec
Page 85 and 86:
This chapter lists the symbologies
Page 87 and 88:
Enter Programming Enable Symbo
Page 89 and 90:
Enter Programming Code 39 S
Page 91:
Enter Programming Code 39 M
Page 94 and 95:
7 Check Digit Verification: When
Page 96 and 97:
7 Codabar Minimum and Maximum Le
Page 98 and 99:
7 UPC Addenda: This feature is u
Page 100 and 101:
7 EAN Addenda: This feature is u
Page 102 and 103:
7 Code 2 of 5: The 3060/3080
Page 104 and 105:
7 Code 2 of 5 Minimum and Max
Page 106 and 107:
7 IATA Setting: The IATA is a Co
Page 108 and 109:
7 Code 11: Generally, the Code
Page 110 and 111:
7 Code 93: Code 93 was designed
Page 112 and 113:
7 MSI/Plessey: One or two check
Page 114 and 115:
7 UK/Plessey: The UK/Plessey bar
Page 116 and 117:
7 UCC/EAN-128: The UCC/EAN-128 c
Page 119 and 120:
Welch Allyn provides service for it
Page 121 and 122:
For service in Japan, please contac
Page 123:
Environmental Specifications Operat
Page 126 and 127:
A No. Description Beeping Buzzer
Page 128:
A If you wish to return the
Page 132:
3060/80/UG Rev C Data Collection Di
show all

Untitled

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?