Untitled

More documents

Recommendations

Info

3 Output Polarity: Wand Emulation output can be sent as standard with bars (black) high, or reversed with bars (black) low. Initial Signal State: Wand Emulation output can be set for a high or a low signal state. Margin Time: You can use this selection to program a delay before and after the data transmission.
Enter Programming Output Polarity Initial Signal State Margin Time Bar: High (5vdc), Space: Low (0vdc) ✱ . . . . . . . . . . . . . . . . . . . . . . . . 0 Bar: Low (0vdc), Space: High (5vdc) . . . . . . . . . . . . . . . . . . . . . . . . . . 1 High level (5VDC) ✱ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 Low level (0VDC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 10 mseconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 15 mseconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 20 mseconds ✱ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 25 mseconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 30 mseconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 50 mseconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 100 mseconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Exit Programming 3
Page 2 and 3: Disclaimer Welch Allyn ® reserves
Page 4 and 5: The CE mark on the product indicate
Page 6 and 7: Section 3 Tailoring the Interface (
Page 8 and 9: Section 5 Building the Message Stri
Page 10 and 11: Section 7 Symbologies (continued) S
Page 13 and 14: VALUETEAM 3060 or 3080 Hand held CC
Page 15 and 16: Reading Width VT3060 60mm 2.3” VT
Page 17 and 18: Disconnect power to your terminal/c
Page 19: To program each option, you must: 1
Page 22 and 23: 2 To program the scanner for your t
Page 25: Once you have programmed your Termi
Page 28 and 29: 3 Output Style: Regular is used
Page 30 and 31: 3 Keyboard Layout: This selecti
Page 33 and 34: Word Length/Parity . . . . . . . .
Page 35 and 36: Enter Programming Word Length/
Page 37 and 38: Enter Programming Baud Rate Ha
Page 39 and 40: Enter Programming Time Out Con
Page 41: Initial signal state Margin time Ex
Page 45: Enter Programming Module Time
Page 49 and 50: Beeper Tone . . . . . . . . . . . .
Page 51 and 52: Enter Programming Beeper Ton
Page 53 and 54: Enter Programming Trigger Mo
Page 55 and 56: Enter Programming Low Power
Page 57: Enter Programming Reread Del
Page 60 and 61: 5 The following diagram illu
Page 62 and 63: 5 Prefix: Prefix Prefix Code ID
Page 64 and 65: 5 Example: Add a prefix or suff
Page 66 and 67: 5 Some terminals drop informati
Page 68 and 69: 5 The following diagram illus
Page 70 and 71: 5 STX/ETX: STX Prefix Code ID S
Page 72 and 73: 5 Prefix and Suffix Code ID: P
Page 74 and 75: 5 Prefix/Suffix Code ID Bar Co
Page 77: The Data Editor selections are used
Page 80 and 81: 6 The Data Editor is used to ed
Page 82 and 83: 6 The Data Editor Control chec
Page 85 and 86: This chapter lists the symbologies
Page 87 and 88: Enter Programming Enable Symbo
Page 89 and 90: Enter Programming Code 39 S
Page 91: Enter Programming Code 39 M
Page 94 and 95:
7 Check Digit Verification: When
Page 96 and 97:
7 Codabar Minimum and Maximum Le
Page 98 and 99:
7 UPC Addenda: This feature is u
Page 100 and 101:
7 EAN Addenda: This feature is u
Page 102 and 103:
7 Code 2 of 5: The 3060/3080
Page 104 and 105:
7 Code 2 of 5 Minimum and Max
Page 106 and 107:
7 IATA Setting: The IATA is a Co
Page 108 and 109:
7 Code 11: Generally, the Code
Page 110 and 111:
7 Code 93: Code 93 was designed
Page 112 and 113:
7 MSI/Plessey: One or two check
Page 114 and 115:
7 UK/Plessey: The UK/Plessey bar
Page 116 and 117:
7 UCC/EAN-128: The UCC/EAN-128 c
Page 119 and 120:
Welch Allyn provides service for it
Page 121 and 122:
For service in Japan, please contac
Page 123:
Environmental Specifications Operat
Page 126 and 127:
A No. Description Beeping Buzzer
Page 128:
A If you wish to return the
Page 132:
3060/80/UG Rev C Data Collection Di
show all

Untitled

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?