Untitled

More documents

Recommendations

Info

Editor Control . . . . . . . . . . . . . . . . . . Disable 1st Insertion . . . . . . . . . . . . . . . . . . . Disable 2nd Insertion . . . . . . . . . . . . . . . . . . . Disable 3rd Insertion . . . . . . . . . . . . . . . . . . . Disable 4th Insertion . . . . . . . . . . . . . . . . . . . Disable Symbology Control . . . . . . . . . . . . . Disable Check Data Length . . . . . . . . . . . . . Disable 1st Check Character . . . . . . . . . . . . Disable 2nd Check Character . . . . . . . . . . . Disable If you program changes to any Data Editor options, and later wish to reset the scanner to the defaulted values, scan the Default Data Editor Settings bar code below. This will reset the scanner to all the defaulted values for the Data Editor. Default Data Editor Settings 6
Page 2 and 3:
Disclaimer Welch Allyn ® reserves
Page 4 and 5:
The CE mark on the product indicate
Page 6 and 7:
Section 3 Tailoring the Interface (
Page 8 and 9:
Section 5 Building the Message Stri
Page 10 and 11:
Section 7 Symbologies (continued) S
Page 13 and 14:
VALUETEAM 3060 or 3080 Hand held CC
Page 15 and 16:
Reading Width VT3060 60mm 2.3” VT
Page 17 and 18:
Disconnect power to your terminal/c
Page 19:
To program each option, you must: 1
Page 22 and 23:
2 To program the scanner for your t
Page 25:
Once you have programmed your Termi
Page 28 and 29: 3 Output Style: Regular is used
Page 30 and 31: 3 Keyboard Layout: This selecti
Page 33 and 34: Word Length/Parity . . . . . . . .
Page 35 and 36: Enter Programming Word Length/
Page 37 and 38: Enter Programming Baud Rate Ha
Page 39 and 40: Enter Programming Time Out Con
Page 41 and 42: Initial signal state Margin time Ex
Page 43 and 44: Enter Programming Output Pola
Page 45: Enter Programming Module Time
Page 49 and 50: Beeper Tone . . . . . . . . . . . .
Page 51 and 52: Enter Programming Beeper Ton
Page 53 and 54: Enter Programming Trigger Mo
Page 55 and 56: Enter Programming Low Power
Page 57: Enter Programming Reread Del
Page 60 and 61: 5 The following diagram illu
Page 62 and 63: 5 Prefix: Prefix Prefix Code ID
Page 64 and 65: 5 Example: Add a prefix or suff
Page 66 and 67: 5 Some terminals drop informati
Page 68 and 69: 5 The following diagram illus
Page 70 and 71: 5 STX/ETX: STX Prefix Code ID S
Page 72 and 73: 5 Prefix and Suffix Code ID: P
Page 74 and 75: 5 Prefix/Suffix Code ID Bar Co
Page 77: The Data Editor selections are used
Page 81 and 82: Enter Programming Editor Control
Page 83: Enter Programming Symbology Control
Page 86 and 87: 7 The 3060/3080 scanner is prese
Page 88 and 89: 7 Standard Code 39: The standar
Page 90 and 91: 7 Code 39 Minimum and Maximum L
Page 93 and 94: Standard Codabar: The standard Coda
Page 95 and 96: Enter Programming Codabar Se
Page 97 and 98: Enter Programming Codabar Mi
Page 99 and 100: Enter Programming UPC Select
Page 101 and 102: Enter Programming EAN/CAN/JA
Page 103 and 104: Enter Programming Code 2
Page 105 and 106: Enter Programming Code 2
Page 107 and 108: Enter Programming IATA Selec
Page 109 and 110: Enter Programming Code 11 C
Page 111 and 112: Enter Programming Code 93 C
Page 113 and 114: Enter Programming MSI/Plesse
Page 115 and 116: Enter Programming UK/Plessey
Page 117: Enter Programming UCC/EAN-12
Page 120 and 121: 8 In the United States, please cont
Page 122 and 123: 8 Welch Allyn, Inc., hereby warra
Page 125 and 126: The Appendix lists the beeping indi
Page 127 and 128: The Keyboard Function Code Table is
Page 130:
A B C D E F 0 (YES) 1 (NO) 2
show all

Untitled

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?