Untitled

More documents

Recommendations

Info

Output Style . . . . . . . . . . . . . . . . . . . Regular Upper/Lower Case . . . . . . . . . . . . . Normal Case Numeric Keypad Mode . . . . . . . . . . Numeric Keypad Mode Off Function Key Emulation . . . . . . . . . Disable ASCII 00-31 Code Output Keyboard Layout . . . . . . . . . . . . . . . USA If you program changes to any Keyboard Wedge Interface options, and later wish to reset the scanner to the defaulted values, scan the Default Keyboard Wedge Settings bar code below. This will reset the scanner to all the defaulted values for the Keyboard Wedge Interface. Default Keyboard Wedge Settings 3
Page 2 and 3: Disclaimer Welch Allyn ® reserves
Page 4 and 5: The CE mark on the product indicate
Page 6 and 7: Section 3 Tailoring the Interface (
Page 8 and 9: Section 5 Building the Message Stri
Page 10 and 11: Section 7 Symbologies (continued) S
Page 13 and 14: VALUETEAM 3060 or 3080 Hand held CC
Page 15 and 16: Reading Width VT3060 60mm 2.3” VT
Page 17 and 18: Disconnect power to your terminal/c
Page 19: To program each option, you must: 1
Page 22 and 23: 2 To program the scanner for your t
Page 25: Once you have programmed your Termi
Page 29 and 30: Enter Programming Output Styl
Page 31: Enter Programming Keyboard La
Page 34 and 35: 3 Word Length/Parity:
Page 36 and 37: 3 Baud Rate:
Page 38 and 39: 3 Time Out Control: This allows
Page 40 and 41: 3 Output Polarity . . .
Page 42 and 43: 3 Output Polarity: Wand Emulati
Page 44 and 45: 3 Module Time: This selection p
Page 47: The Scanner Set Up selections allow
Page 50 and 51: 4 Beeper Tone: This selection
Page 52 and 53: 4 Trigger Mode Manual Trigger,
Page 54 and 55: 4 Low Power Trigger Delay: Whe
Page 56 and 57: 4 Reread Delay: This selection
Page 59 and 60: When a bar code is scanned, additio
Page 61 and 62: Prefix . . . . . . . . . . . . . .
Page 63 and 64: Enter Programming Prefix Suff
Page 65 and 66: Hex to ASCII Conversion Chart
Page 67 and 68: Enter Programming Intercharacter De
Page 69 and 70: STX . . . . . . . . . . . . . . . .
Page 71 and 72: Enter Programming STX/ETX Rec
Page 73 and 74: Enter Programming Prefix/Suffix Cod
Page 75: Enter Programming Prefix/Suff
Page 79 and 80:
Editor Control . . . . . . . . . .
Page 81 and 82:
Enter Programming Editor Control
Page 83:
Enter Programming Symbology Control
Page 86 and 87:
7 The 3060/3080 scanner is prese
Page 88 and 89:
7 Standard Code 39: The standar
Page 90 and 91:
7 Code 39 Minimum and Maximum L
Page 93 and 94:
Standard Codabar: The standard Coda
Page 95 and 96:
Enter Programming Codabar Se
Page 97 and 98:
Enter Programming Codabar Mi
Page 99 and 100:
Enter Programming UPC Select
Page 101 and 102:
Enter Programming EAN/CAN/JA
Page 103 and 104:
Enter Programming Code 2
Page 105 and 106:
Enter Programming Code 2
Page 107 and 108:
Enter Programming IATA Selec
Page 109 and 110:
Enter Programming Code 11 C
Page 111 and 112:
Enter Programming Code 93 C
Page 113 and 114:
Enter Programming MSI/Plesse
Page 115 and 116:
Enter Programming UK/Plessey
Page 117:
Enter Programming UCC/EAN-12
Page 120 and 121:
8 In the United States, please cont
Page 122 and 123:
8 Welch Allyn, Inc., hereby warra
Page 125 and 126:
The Appendix lists the beeping indi
Page 127 and 128:
The Keyboard Function Code Table is
Page 130:
A B C D E F 0 (YES) 1 (NO) 2
show all

Untitled

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?