Modular Multitrack Recorder - Tascam

More documents

Recommendations

Info

CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: Replace battery with Panasonic or Maxell, model CR2032 only. Use of another battery may present a risk of fire or explosion. See owner’s manual for safety instructions For U.S.A TO THE USER This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION Changes or modifications to this equipment not expressly approved by TEAC CORPORATION for compliance could void the user's authority to operate this equipment. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Alternating Current Protective Conductor Terminal
IMPORTANT SAFETY INSTRUCTIONS CONSIGNES DE SECURITE SICHERHEITSHINWEISE NORME DI SICUREZZA INSTRUCCIONES DE SEGURIDAD VEILIGHEIDSVOORSCHRIFTEN TEAC CORPORATION
Page 1: » MMR-8 Modular Multitrack Recorde
Page 10 and 11: TEAC CORPORATION 3-7-3, Nakacho, Mu
Page 12 and 13: Chapter 3 MMR-8 Operation..........
Page 14 and 15: 8 Appendix D: MMR-8 Cable Informati
Page 16 and 17: The MMR-8 will directly play back m
Page 18 and 19: Functional Overview The MMR-8 opera
Page 20 and 21: 14 Figure 1-3. MMR-8 Panel/Display
Page 22 and 23: Electrical Ratings: 16 115 VAC @ 2A
Page 24 and 25: General Guidelines Mounting Rack Ea
Page 26 and 27: AC Mains and Grounding (Earthing) C
Page 28 and 29: Audio Connections All audio inputs
Page 30 and 31: Biphase Connections Biphase is a co
Page 32 and 33: Serial Transport Connection The TRA
Page 34 and 35: Powering Up the System The MMR-8 co
Page 36 and 37: Factory Default Settings The MMR-8
Page 38 and 39: 32 Tascam MMR-8 User’s Guide •
Page 40 and 41: Mode This term is used to refer to
Page 43 and 44: Front Panel Indicators, Switches, a
Page 45 and 46: Liquid Crystal Display (LCD) The LC
Page 47 and 48: Slip Track State Display In the Sli
Page 49 and 50: Front Panel Key Groups The MMR-8 fr
Page 51 and 52: SHIFT+UP ARROW (TC/FEET) SHIFT+TRIM
Page 53 and 54:
SEL (TRACK SELECT) SHIFT+SEL (vario
Page 55 and 56:
Insert Insert places the contents o
Page 57 and 58:
Edit Sync Mode The setting chosen i
Page 59 and 60:
SHIFT + LOAD TRACK (DELETE) As with
Page 61 and 62:
Keypad Group These keys are located
Page 63 and 64:
HEAD (SHIFT+8) NEXT EDIT (SHIFT+9)
Page 65 and 66:
LOOP Pressing the Loop key prepares
Page 67 and 68:
Basic Operation Loading and Mountin
Page 69 and 70:
Once a track is loaded into a track
Page 71 and 72:
Trimming Time Code Values Any time
Page 73 and 74:
The Setup State & the Setup Menus C
Page 75 and 76:
Setup Menu Chart This chart lists a
Page 77 and 78:
MENU # MENU NAME PARAMETERS 301 Bip
Page 79 and 80:
Setup Menu Details This section con
Page 81 and 82:
The Lynx Bus The Lynx bus allows co
Page 83 and 84:
Record Mode Menu 200, Record Mode,
Page 85 and 86:
Chapter 5 MMR-8 System Applications
Page 87 and 88:
Menu 300 is used to set the Biphase
Page 89 and 90:
Chapter 6 Maintenance & Service The
Page 91 and 92:
MIC Calibration Procedure Follow th
Page 93 and 94:
For technical support on the MMR-8
Page 95 and 96:
Appendix A: Control Panel Command S
Page 97 and 98:
SHIFT+6 Locate to Previous Edit poi
Page 99 and 100:
Appendix B: TASCAM MMR-8 Drive Comp
Page 101 and 102:
Appendix C: WaveFrame Compatibility
Page 103 and 104:
Appendix D: MMR-8 Cable Information
Page 105 and 106:
TRANSPORT (Sony 9-pin) Connector pi
Page 107 and 108:
DIO (AES/EBU Digital Audio) Connect
Page 109 and 110:
VITC IN Connector NOTES: SERIAL CON
Page 111 and 112:
Appendix E: MMR-8 Glossary Abbrevia
Page 113 and 114:
Abbreviations and Terms Definitions
Page 115 and 116:
Abbreviations and Terms Definitions
Page 117 and 118:
Index 2 24-BIT REC LED ............
Page 119 and 120:
In Point...........................
Page 121 and 122:
Reverse Play Key...................
Page 123:
Tascam MMR-8 Owner’s Manual • I
show all

Modular Multitrack Recorder - Tascam

Create successful ePaper yourself

Delete template?

Save as template?