Manual NISE 3500 - ICPDAS-EUROPE

More documents

Recommendations

Info

Appendix E: Intel Manageability Command Tool-KVM 7. The newly added iAMT computer with its IP address will appear under the Network list located at the left column of the screen. 8. On the left column, under Network, select the iAMT computer. The Connect & Control screen will appear on the right side. Select the Connection tab and then click Connect. The Manageability Commander Tool will connect the iAMT computer with the server. Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 99 NISE 3500, NISE 3500M User Manual
Appendix E: Intel Manageability Command Tool-KVM 9. The iAMT computer’s icon under the Network list will turn from gray to blue. The server and iAMT computer are now connected. 10. Display the hierarchical structure of the iAMT computer’s files and folders. This will allow you to view the remote computer’s hardware status and configuration. Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 100 NISE 3500, NISE 3500M User Manual
Page 1 and 2:
NEXCOM International Co., Ltd. Indu
Page 3 and 4:
Contents Serial Interface (COM 1 -
Page 5 and 6:
Preface RoHS Compliance NEXCOM RoHS
Page 7 and 8:
Preface Warnings Read and adhere to
Page 9 and 10:
Preface Technical Support and Assis
Page 11 and 12:
Preface China-Beijing Room 301, Blo
Page 13 and 14:
Preface Ordering Information The fo
Page 15 and 16:
Chapter 1: Product Introduction NIS
Page 17 and 18:
Chapter 1: Product Introduction Pow
Page 19 and 20:
Chapter 1: Product Introduction Rea
Page 21 and 22:
Chapter 2: Jumpers and Connectors T
Page 23 and 24:
1 1 1 Locations of the Jumpers and
Page 25 and 26:
Jumpers Clear CMOS Connector size:
Page 27 and 28:
IEEE1394b Connector (NISE 3500M onl
Page 29 and 30:
ATX Power On/Off Switch Connector l
Page 31 and 32:
9V-30V DC Input Connector type: POW
Page 33 and 34:
COM1 (RS232) labelled “A“ on DB
Page 35 and 36:
USB Ports Connector type: Dual USB
Page 37 and 38:
Mic-in Jack Connector size: 5-pin j
Page 39 and 40:
SMBus DATA/CLK Pin Header Connector
Page 41 and 42:
LVDS Backlight Connector Connector
Page 43 and 44:
SATA DOM Power Connectors Connector
Page 45 and 46:
Line-in Connector Connector type: 1
Page 47 and 48:
Parallel Connector Connector size:
Page 49 and 50:
Installing a DIMM 1. Push the eject
Page 51 and 52:
Installing the CPU 1. The CPU socke
Page 53 and 54:
5. Before you install the heat sink
Page 55 and 56:
4. Place the SATA hard drive on the
Page 57 and 58:
Installing a Half Length SATA DOM w
Page 59 and 60:
Installing a Full Length SATA DOM I
Page 61 and 62: Wallmount Brackets The wallmount br
Page 63 and 64: Default Configuration Most of the c
Page 65 and 66: Advanced The Advanced menu allows y
Page 67 and 68: Limit CPUID Maximum The CPUID instr
Page 69 and 70: USB Configuration This section is u
Page 71 and 72: AMT Configuration This section is u
Page 73 and 74: South Bridge SB Chipset Configurat
Page 75 and 76: Boot Main Advanced Boot Configurati
Page 77 and 78: Chapter 5: AMT Settings Enable Inte
Page 79 and 80: 3. Enter a new password in the spac
Page 81 and 82: 7. Select Network Setup and then pr
Page 83 and 84: 11. In the TCP/IP Settings menu, se
Page 85 and 86: 15. Select Default Gateway Address
Page 87 and 88: 19. In the Intel(R) ME Platform Con
Page 89 and 90: 23. Select Previous Menu until you
Page 91 and 92: 27. In the SOL/IDER menu, select SO
Page 93 and 94: 31. Select Previous Menu until you
Page 95 and 96: 35. Select Previous Menu. Intel(R)
Page 97 and 98: 3. The message below will appear. T
Page 99 and 100: Appendix A: Power Consumption Power
Page 101 and 102: Appendix C: Watchdog Timer Setting
Page 103 and 104: Appendix D: Intel Embedded AMT Mana
Page 111: Appendix E: Intel Manageability Com
Page 115 and 116: Appendix E: Intel Manageability Com
Page 117 and 118: Appendix F: External Anti-vibration
Page 119 and 120: Appendix F: External Anti-vibration
show all

Manual NISE 3500 - ICPDAS-EUROPE

Create successful ePaper yourself

Delete template?

Save as template?