Manual NISE 3500 - ICPDAS-EUROPE

More documents

Recommendations

Info

Chapter 1: Product Introduction Mechanical Dimensions NISE 3500/3500M 184.00 224.00 264.00 268.00 195.00 207.00 219.00 80.00 86.00 Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 7 NISE 3500, NISE 3500M User Manual
Chapter 2: Jumpers and Connectors This chapter describes how to set the jumpers on the motherboard. Note that the following procedures are generic for all NISE 3500 series. Before You Begin • Ensure you have a stable, clean working environment. Dust and dirt can get into components and cause a malfunction. Use containers to keep small components separated. • Adequate lighting and proper tools can prevent you from accidentally damaging the internal components. Most of the procedures that follow require only a few simple tools, including the following: • A Philips screwdriver • A flat-tipped screwdriver • A set of jewelers Screwdrivers • A grounding strap • An anti-static pad • Using your fingers can disconnect most of the connections. It is recommended that you do not use needle-nosed pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors. • Before working on internal components, make sure that the power is off. Ground yourself before touching any internal components, by touching a metal object. Static electricity can damage many of the electronic components. Humid environment tend to have less static electricity than dry environments. A grounding strap is warranted whenever danger of static electricity exists. Precautions Computer components and electronic circuit boards can be damaged by discharges of static electricity. Working on the computers that are still connected to a power supply can be extremely dangerous. Follow the guidelines below to avoid damage to your computer or yourself: • Always disconnect the unit from the power outlet whenever you are working inside the case. • If possible, wear a grounded wrist strap when you are working inside the computer case. Alternatively, discharge any static electricity by touching the bare metal chassis of the unit case, or the bare metal body of any other grounded appliance. • Hold electronic circuit boards by the edges only. Do not touch the components on the board unless it is necessary to do so. Don’t flex or stress the circuit board. • Leave all components inside the static-proof packaging that they shipped with until they are ready for installation. • Use correct screws and do not over tighten screws. Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 8 NISE 3500, NISE 3500M User Manual
Page 1 and 2: NEXCOM International Co., Ltd. Indu
Page 3 and 4: Contents Serial Interface (COM 1 -
Page 5 and 6: Preface RoHS Compliance NEXCOM RoHS
Page 7 and 8: Preface Warnings Read and adhere to
Page 9 and 10: Preface Technical Support and Assis
Page 11 and 12: Preface China-Beijing Room 301, Blo
Page 13 and 14: Preface Ordering Information The fo
Page 15 and 16: Chapter 1: Product Introduction NIS
Page 17 and 18: Chapter 1: Product Introduction Pow
Page 19: Chapter 1: Product Introduction Rea
Page 23 and 24: 1 1 1 Locations of the Jumpers and
Page 25 and 26: Jumpers Clear CMOS Connector size:
Page 27 and 28: IEEE1394b Connector (NISE 3500M onl
Page 29 and 30: ATX Power On/Off Switch Connector l
Page 31 and 32: 9V-30V DC Input Connector type: POW
Page 33 and 34: COM1 (RS232) labelled “A“ on DB
Page 35 and 36: USB Ports Connector type: Dual USB
Page 37 and 38: Mic-in Jack Connector size: 5-pin j
Page 39 and 40: SMBus DATA/CLK Pin Header Connector
Page 41 and 42: LVDS Backlight Connector Connector
Page 43 and 44: SATA DOM Power Connectors Connector
Page 45 and 46: Line-in Connector Connector type: 1
Page 47 and 48: Parallel Connector Connector size:
Page 49 and 50: Installing a DIMM 1. Push the eject
Page 51 and 52: Installing the CPU 1. The CPU socke
Page 53 and 54: 5. Before you install the heat sink
Page 55 and 56: 4. Place the SATA hard drive on the
Page 57 and 58: Installing a Half Length SATA DOM w
Page 59 and 60: Installing a Full Length SATA DOM I
Page 61 and 62: Wallmount Brackets The wallmount br
Page 63 and 64: Default Configuration Most of the c
Page 65 and 66: Advanced The Advanced menu allows y
Page 67 and 68: Limit CPUID Maximum The CPUID instr
Page 69 and 70: USB Configuration This section is u
Page 71 and 72:
AMT Configuration This section is u
Page 73 and 74:
South Bridge SB Chipset Configurat
Page 75 and 76:
Boot Main Advanced Boot Configurati
Page 77 and 78:
Chapter 5: AMT Settings Enable Inte
Page 79 and 80:
3. Enter a new password in the spac
Page 81 and 82:
7. Select Network Setup and then pr
Page 83 and 84:
11. In the TCP/IP Settings menu, se
Page 85 and 86:
15. Select Default Gateway Address
Page 87 and 88:
19. In the Intel(R) ME Platform Con
Page 89 and 90:
23. Select Previous Menu until you
Page 91 and 92:
27. In the SOL/IDER menu, select SO
Page 93 and 94:
31. Select Previous Menu until you
Page 95 and 96:
35. Select Previous Menu. Intel(R)
Page 97 and 98:
3. The message below will appear. T
Page 99 and 100:
Appendix A: Power Consumption Power
Page 101 and 102:
Appendix C: Watchdog Timer Setting
Page 103 and 104:
Appendix D: Intel Embedded AMT Mana
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Appendix E: Intel Manageability Com
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Appendix F: External Anti-vibration
Page 119 and 120:
Appendix F: External Anti-vibration
show all

Manual NISE 3500 - ICPDAS-EUROPE

Create successful ePaper yourself

Delete template?

Save as template?