- Page 1 and 2:
NEXCOM International Co., Ltd. Indu
- Page 3 and 4:
Contents Serial Interface (COM 1 -
- Page 5 and 6:
Preface RoHS Compliance NEXCOM RoHS
- Page 7 and 8:
Preface Warnings Read and adhere to
- Page 9 and 10:
Preface Technical Support and Assis
- Page 11 and 12:
Preface China-Beijing Room 301, Blo
- Page 13 and 14:
Preface Ordering Information The fo
- Page 15 and 16:
Chapter 1: Product Introduction NIS
- Page 17 and 18:
Chapter 1: Product Introduction Pow
- Page 19 and 20:
Chapter 1: Product Introduction Rea
- Page 21 and 22:
Chapter 2: Jumpers and Connectors T
- Page 23 and 24:
1 1 1 Locations of the Jumpers and
- Page 25 and 26:
Jumpers Clear CMOS Connector size:
- Page 27 and 28:
IEEE1394b Connector (NISE 3500M onl
- Page 29 and 30:
ATX Power On/Off Switch Connector l
- Page 31 and 32:
9V-30V DC Input Connector type: POW
- Page 33 and 34:
COM1 (RS232) labelled “A“ on DB
- Page 35 and 36:
USB Ports Connector type: Dual USB
- Page 37 and 38:
Mic-in Jack Connector size: 5-pin j
- Page 39 and 40:
SMBus DATA/CLK Pin Header Connector
- Page 41 and 42:
LVDS Backlight Connector Connector
- Page 43 and 44:
SATA DOM Power Connectors Connector
- Page 45 and 46:
Line-in Connector Connector type: 1
- Page 47 and 48:
Parallel Connector Connector size:
- Page 49 and 50:
Installing a DIMM 1. Push the eject
- Page 51 and 52:
Installing the CPU 1. The CPU socke
- Page 53 and 54:
5. Before you install the heat sink
- Page 55 and 56:
4. Place the SATA hard drive on the
- Page 57 and 58:
Installing a Half Length SATA DOM w
- Page 59 and 60:
Installing a Full Length SATA DOM I
- Page 61 and 62:
Wallmount Brackets The wallmount br
- Page 63 and 64:
Default Configuration Most of the c
- Page 65 and 66: Advanced The Advanced menu allows y
- Page 67 and 68: Limit CPUID Maximum The CPUID instr
- Page 69 and 70: USB Configuration This section is u
- Page 71 and 72: AMT Configuration This section is u
- Page 73 and 74: South Bridge SB Chipset Configurat
- Page 75 and 76: Boot Main Advanced Boot Configurati
- Page 77 and 78: Chapter 5: AMT Settings Enable Inte
- Page 79 and 80: 3. Enter a new password in the spac
- Page 81 and 82: 7. Select Network Setup and then pr
- Page 83 and 84: 11. In the TCP/IP Settings menu, se
- Page 85 and 86: 15. Select Default Gateway Address
- Page 87 and 88: 19. In the Intel(R) ME Platform Con
- Page 89 and 90: 23. Select Previous Menu until you
- Page 91 and 92: 27. In the SOL/IDER menu, select SO
- Page 93 and 94: 31. Select Previous Menu until you
- Page 95 and 96: 35. Select Previous Menu. Intel(R)
- Page 97 and 98: 3. The message below will appear. T
- Page 99 and 100: Appendix A: Power Consumption Power
- Page 101 and 102: Appendix C: Watchdog Timer Setting
- Page 103 and 104: Appendix D: Intel Embedded AMT Mana
- Page 105 and 106: Appendix D: Intel Embedded AMT Mana
- Page 107 and 108: Appendix D: Intel Embedded AMT Mana
- Page 109 and 110: Appendix D: Intel Embedded AMT Mana
- Page 111 and 112: Appendix E: Intel Manageability Com
- Page 113 and 114: Appendix E: Intel Manageability Com
- Page 115: Appendix E: Intel Manageability Com
- Page 119 and 120: Appendix F: External Anti-vibration