Structure of Actuator KNX S-B4T-UP 230 V AC - IQmarket

More documents

Recommendations

Info

If “Use shading automatic: Yes“ has been selected: Brightness: -------------------------------------- Type of shading input 1 x 1 Bit • 1 x 16 Bit • 2 x 16 Bit • 3 x 16 Bit Up-movement delay in min 0 … 255 Down-movement delay in min 0 … 30 If “Type of shading input 1 x 16 bit / 2 x 16 bit / 3 x 16 bit“ has been selected: The measured values of one, two or three light sensors may be evaluated. The highest value is the value which is always relevant for the reaction. Shading threshold value standard by Parameter • Communication object If “Shading threshold standard by parameter” has been selected: Shading threshold value standard by Parameter Shading threshold value in klux 0 … 100 Up-movement delay in min 0 … 255 Down-movement delay in min 0 … 30 Send current shading status No • Yes If “Shading threshold standard by communication object” has been selected: Shading threshold value standard by The last-communicated value shall be maintained Starting threshold value in klux valid until 1st communication Type of threshold value change Step size in klux (only in case of “Increment/decrement with comm. object”) Communication object • not • after restoration of voltage • after restoration of voltage and programming 0 … 100 • Absolute value with 16 bit comm. object • Increment/decrement with one comm. object • Increment/decrement with two comm.objects 1 … 5 Up-movement delay in min 0 … 255 Down-movement delay in min 0 … 30 Send current shading status No • Yes Position of the sun: -------------------------------------- Evaluate the position of the sun No • Yes If “Evaluate of the position of the sun: Yes“ has been selected: Evaluate the position of the sun Yes 21
Position of the sun is defined by • discrete values of azimuth and elevation • directions (in terms of azimuth/elevation) If “Position of the sun is defined by discrete values“ has been selected: Azimuth from 0 … 360 Azimuth up to 0 … 360 Elevation from 0 … 90 Elevation up to 0 … 90 If “Position of the sun is defined by directions“ has been selected: Direction • East (azimuth: 0° … 180°) • Southeast (azimuth: 45° … 225°) • South (azimuth: 90° … 270°) • Southwest (azimuth: 135° … 315°) • West (azimuth: 180° … 360°) Slat and travel position: -------------------------------------- Note: Slats are closed at 100% and horizontal at 50%. Shall slats follow elevation No • Yes If “Shall slats follow elevation: No” has been selected: Shall slats follow elevation No Slat position in % 0 … 100 Blind position in % 0 … 100 Use learning object for new shading positions No • Yes If “Use learning object for new shading positions: Yes” has been selected, a new shading position may be learned (travel position and slat angle). For this purpose, the shading is moved manually to any position first and learns by means of 41 “Shading position learning object“. In case of sun, the automatic then moves to the learned position. If “Shall slats follow elevation: Yes” has been selected, the elevation angles and the according slat positions may be set. Three elevation angles may be set: in case of elevation below (in degree) 0 … 90 Slat position in % 0 … 100 otherwise Slat position in % 0 … 100 Blind position in % 0 … 100 Use learning object for new shading positions No • Yes If “Use learning object for new shading positions: Yes” has been selected, a new shading position may be learned (only travel position, slats turn to elevation). For this purpose, the shading is moved manually to any position first and learns by means of 41 22
Page 1 and 2: KNX S-B4T-UP 230 V and KNX S-B4T-UP
Page 3 and 4: KNX S-B4T-UP • from software vers
Page 5 and 6: Current: Output: Inputs: Data outpu
Page 7 and 8: Installation and Commissioning Inst
Page 9 and 10: No. Name Function Flags DP type 21
Page 11 and 12: No. Name Function Flags DP type 86
Page 13 and 14: Setting of parameters General setti
Page 15 and 16: If “Accomplish reference run: Yes
Page 17 and 18: If “Use operating range limit: Ye
Page 19 and 20: In case of automatic operation afte
Page 21: Dawn control / time control Use daw
Page 25 and 26: Roller shutter control The setting
Page 27 and 28: Travel position for slave in % if i
Page 29 and 30: Change from manual to automatic Man
Page 31 and 32: Dawn control / time control Use daw
Page 33 and 34: Position of the sun is defined by
Page 35 and 36: Awning control The setting options
Page 37 and 38: Monitoring period for zero position
Page 39 and 40: In case of automatic operation afte
Page 41 and 42: Dawn control / time control Use daw
Page 43 and 44: Position of the sun is defined by
Page 45 and 46: Window control Use operating range
Page 47 and 48: (Zero position sensor at input 4 of
Page 49 and 50: Change from manual to automatic Man
Page 51 and 52: If “Use coercive ventilation: Yes
Page 53 and 54: If “Type of input object 1 bit“
Page 55 and 56: Inverted standard control mode In c
Page 57 and 58: Send value Send value every (only i
Page 59 and 60: Brightness encoder If “Bus functi
Page 61 and 62: Temperature sensor For the “Gener
Page 63 and 64: If “Threshold value standard per
Page 65 and 66: Zero position sensor master over bu

Structure of Actuator KNX S-B4T-UP 230 V AC - IQmarket

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?