Structure of Actuator KNX S-B4T-UP 230 V AC - IQmarket

More documents

Recommendations

Info

Internal and total measured value • do not send • send cyclical • send in case of change • in case of change and cyclical All further settings refer to the total measured value! Use min. and max. temperature values No • Yes The temperature values are not maintained after a reset. Use malfunction object Use threshold 1 / 2 No • Yes No • Yes Threshold 1 / 2 (temperature sensor) Threshold value: -------------------------------------- Threshold value standard per Parameter • Communication object If “Threshold value standard per parameter” has been selected: Threshold value standard per Parameter Threshold value in 0.1 °C -300 … 800 Hysteresis of threshold value in 0.1 °C. 0 … 100 61
If “Threshold value standard per communication object” has been selected: The las- communicated value shall be maintained Starting threshold in 0.1 °C valid until 1st communication (only if the value communicated at last “does not” remain or remains “after the return of voltage”) Type of threshold value change Step size (only if threshold value changes by „ Increment/decrement …”) • not • after restoration of voltage • after restoration of voltage and programming -300 … 800 • Absolute value with 16 bit comm. object • Increment/decrement with one comm. object • Increment/decrement with two comm.objects 0,1°C • 0,2°C • 0,3°C • 0,4°C • 0,5°C • 1°C • 2°C • 3°C • 4°C • 5°C Hysteresis of threshold value in 0.1 °C 0 … 100 Switching output: -------------------------------------- Output is at (TH = threshold) Switching delay from 0 to 1 Switching delay from 1 to 0 Switching output sends Send switching output cyclically every (only if “… and cyclical“ has been selected) • TV above = 1 | TV - Hyst. below = 0 • TV above = 0 | TV - Hyst. below = 1 • TV below = 1 | TV + Hyst. above = 0 • TV below = 0 | TV + Hyst. above = 1 no • 1 sec … 2 h no • 1 sec … 2 h • in case of change • in case of change to 1 • in case of change to 0 • in case of change and cyclical • in case of change to 1 and cyclical • in case of change to 0 and cyclical 5 s … 2 h Blocking: -------------------------------------- Use block of switching output No • Yes If “Use block of switching output: Yes” has been selected: Use block of switching output Evaluation of the blocking object Value of blocking object before first communication Behaviour of switching output when blocking Yes • if value 1: block | if value 0: release • if value 0: block | if value 1: release 0 • 1 • do not send telegram • send 0 • send 1 62
Page 1 and 2:
KNX S-B4T-UP 230 V and KNX S-B4T-UP
Page 3 and 4:
KNX S-B4T-UP • from software vers
Page 5 and 6:
Current: Output: Inputs: Data outpu
Page 7 and 8:
Installation and Commissioning Inst
Page 9 and 10:
No. Name Function Flags DP type 21
Page 11 and 12: No. Name Function Flags DP type 86
Page 13 and 14: Setting of parameters General setti
Page 15 and 16: If “Accomplish reference run: Yes
Page 17 and 18: If “Use operating range limit: Ye
Page 19 and 20: In case of automatic operation afte
Page 21 and 22: Dawn control / time control Use daw
Page 23 and 24: Position of the sun is defined by
Page 25 and 26: Roller shutter control The setting
Page 27 and 28: Travel position for slave in % if i
Page 29 and 30: Change from manual to automatic Man
Page 35 and 36: Awning control The setting options
Page 37 and 38: Monitoring period for zero position
Page 39 and 40: In case of automatic operation afte
Page 45 and 46: Window control Use operating range
Page 47 and 48: (Zero position sensor at input 4 of
Page 49 and 50: Change from manual to automatic Man
Page 51 and 52: If “Use coercive ventilation: Yes
Page 53 and 54: If “Type of input object 1 bit“
Page 55 and 56: Inverted standard control mode In c
Page 57 and 58: Send value Send value every (only i
Page 59 and 60: Brightness encoder If “Bus functi
Page 61: Temperature sensor For the “Gener
Page 65 and 66: Zero position sensor master over bu
show all

Structure of Actuator KNX S-B4T-UP 230 V AC - IQmarket

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?