Structure of Actuator KNX S-B4T-UP 230 V AC - IQmarket

More documents

Recommendations

Info

Structure of Actuator KNX S-B4T-UP 230 V AC Fig. 1: Front side of KNX S-B4T-UP 230 V 1 Connecting plug terminal binary inputs and temperature sensor 2 Programming LED 3 Programming key (PRG) 4 Inscription space 5 KNX plug terminal +/- Fig. 2: Rear side of KNX S-B4T-UP 230 V 1 Connecting plug terminal for voltage supply and drive mechanism 2 Microfuse T6,3 A Structure of Actuator KNX S-B4T-UP 24 V DC Fig. 3: Front side of KNX S-B4T-UP 24 V 1 Connecting plug terminal binary inputs and temperature sensor 2 Programming LED 3 Programming key (PRG) 4 Inscription space 5 KNX plug terminal +/- Fig. 4: Rear side of KNX S-B4T-UP 24 V 1 Connecting plug terminal for voltage supply and drive mechanism 5
Installation and Commissioning Installation, inspection, commissioning and troubleshooting of the actuators must only be carried out by a competent electrician. Disconnect all lines to be assembled, and take safety precautions against accidental switch-on. The actuators are exclusively intended for appropriate use. With each inappropriate change or non-observance of the instructions for use, any warranty or guarantee claim will be void. After unpacking the device, check immediately for any mechanical damages. In case of transport damage, this must immediately notified to the supplier. If damaged, the actuators must not be put into operation. If an operation without risk may supposedly not be guaranteed, the device must be put out of operation and be secured against accidental operation. The actators must only be operated as stationary system, i.e. only in a fitted state and after completion of all installation and start-up works, and only in the environment intended for this purpose. Elsner Elektronik does not assume any liability for changes in standards after publication of this instruction manual. Connection The actuators are installed in a flush-type socket. The connection is accomplished by a KNX connection clamp at the KNX data bus. Furthermore, a voltage supply (230 V AC or 24 V DC, depending on the version) is necessary. The physical address is allocated by the KNX software. For this purpose, the actuator is provided with a programming key with control LED. Notes on installation Never expose actuators to water (rain) or dust. This might damage the electronic system. A relative air humidity of 95% must not be exceeded. Avoid bedwewing. 6
Page 1 and 2: KNX S-B4T-UP 230 V and KNX S-B4T-UP
Page 3 and 4: KNX S-B4T-UP • from software vers
Page 5: Current: Output: Inputs: Data outpu
Page 9 and 10: No. Name Function Flags DP type 21
Page 11 and 12: No. Name Function Flags DP type 86
Page 13 and 14: Setting of parameters General setti
Page 15 and 16: If “Accomplish reference run: Yes
Page 17 and 18: If “Use operating range limit: Ye
Page 19 and 20: In case of automatic operation afte
Page 21 and 22: Dawn control / time control Use daw
Page 23 and 24: Position of the sun is defined by
Page 25 and 26: Roller shutter control The setting
Page 27 and 28: Travel position for slave in % if i
Page 29 and 30: Change from manual to automatic Man
Page 35 and 36: Awning control The setting options
Page 37 and 38: Monitoring period for zero position
Page 39 and 40: In case of automatic operation afte
Page 45 and 46: Window control Use operating range
Page 47 and 48: (Zero position sensor at input 4 of
Page 49 and 50: Change from manual to automatic Man
Page 51 and 52: If “Use coercive ventilation: Yes
Page 53 and 54: If “Type of input object 1 bit“
Page 55 and 56: Inverted standard control mode In c
Page 57 and 58:
Send value Send value every (only i
Page 59 and 60:
Brightness encoder If “Bus functi
Page 61 and 62:
Temperature sensor For the “Gener
Page 63 and 64:
If “Threshold value standard per
Page 65 and 66:
Zero position sensor master over bu
show all

Structure of Actuator KNX S-B4T-UP 230 V AC - IQmarket

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?