Structure of Actuator KNX S-B4T-UP 230 V AC - IQmarket

More documents

Recommendations

Info

consequence, the slave remains in safe position or it moves back if it is not within the safe range. The master actuator knows from the communication object „Slave zero position status” whether the drive mechanism connected to the slave actuator is already in a safe position (then the master moves immediately) or not (then the master waits). Only if the master actuator is informed that the slave drive mechanism is in a safe position, it moves its drive mechanism beyond its own safe position. You can see an example in the chapter “Blind control: Operating range limit”. Master and slave regularly exchange their positions (“safe“ or “not safe”). By means of the monitoring period, you may adjust the frequency of information retrieval. The selected period should be shorter than the period which the monitored drive mechanism needs to travel from the limit of the safe range (last reported safe position) to a position where there is risk of collision. If the drive mechanism does not receive a master/slave or zero position object, it moves to the safe position. The same holds true for a bus voltage breakdown or for a malfunction message from the zero position sensor (is valid for the parameterisation as master and as slave). If “Use operating range limit: Yes“ has been selected: Actuator is Master • Slave If “Actuator is Master“ has been selected: (Zero position sensor at bus) Actuator is Master Transmission repetition for master command in sec Monitoring period for zero position object and slave status in sec 1 … 255 1 … 255 (Zero position sensor at input 4 of actuator) Actuator is Transmission repetition for master and status command in sec Master 1 … 255 Monitoring period for slave status in sec 1 … 255 If “Actuator is Slave“ has been selected: (Zero position sensor at bus) Actuator is Slave Monitoring period for zero position object and master status in sec 1 … 255 25
Travel position for slave in % if input “Master zero position command“ = 1 0 … 100 (Zero position sensor at input 4 of actuator) Actuator is Slave Transmission repetition for slave status in sec 1 … 255 Monitoring period for master status in sec 1 … 255 Travel position for slave in % if input “Master zero position command“ = 1 0 … 100 Monitoring of alarm and blocking objects If “Monitoring of alarm and blocking objects: Yes” has been selected: Monitoring period for 5 sec … 2h alarm/blocking objects Behaviour in case of non-receipt of an alarm/blocking object Stop • UP-command • DOWN-command The priorities of the following functions correspond with the order in the programme! Note: Alarm and blocking objects block at 1 Alarm object Use alarm object No • Yes If “Use alarm object: Yes“ has been selected: Use alarm object Yes If alarm object value = 1 If alarm object value = 0 In case of manual operation before and after alarm In case of automatic operation after alarm Value of the object before 1st communication and restoration of bus voltage no action • Stop • UP-command • DOWN-command no action • move to last position Follow automatic 0 • 1 Blocking object 1 / 2 Use blocking object 1 Use blocking object 2 No • Yes No • Yes If “Use blocking object 1 / 2: Yes“ has been selected: Settings see ”Alarm object” Wind block Use wind block No • Yes 26
Page 1 and 2: KNX S-B4T-UP 230 V and KNX S-B4T-UP
Page 3 and 4: KNX S-B4T-UP • from software vers
Page 5 and 6: Current: Output: Inputs: Data outpu
Page 7 and 8: Installation and Commissioning Inst
Page 9 and 10: No. Name Function Flags DP type 21
Page 11 and 12: No. Name Function Flags DP type 86
Page 13 and 14: Setting of parameters General setti
Page 15 and 16: If “Accomplish reference run: Yes
Page 17 and 18: If “Use operating range limit: Ye
Page 19 and 20: In case of automatic operation afte
Page 21 and 22: Dawn control / time control Use daw
Page 23 and 24: Position of the sun is defined by
Page 25: Roller shutter control The setting
Page 29 and 30: Change from manual to automatic Man
Page 35 and 36: Awning control The setting options
Page 37 and 38: Monitoring period for zero position
Page 39 and 40: In case of automatic operation afte
Page 45 and 46: Window control Use operating range
Page 47 and 48: (Zero position sensor at input 4 of
Page 49 and 50: Change from manual to automatic Man
Page 51 and 52: If “Use coercive ventilation: Yes
Page 53 and 54: If “Type of input object 1 bit“
Page 55 and 56: Inverted standard control mode In c
Page 57 and 58: Send value Send value every (only i
Page 59 and 60: Brightness encoder If “Bus functi
Page 61 and 62: Temperature sensor For the “Gener
Page 63 and 64: If “Threshold value standard per
Page 65 and 66: Zero position sensor master over bu

Structure of Actuator KNX S-B4T-UP 230 V AC - IQmarket

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?