Structure of Actuator KNX S-B4T-UP 230 V AC - IQmarket

More documents

Recommendations

Info

Roller shutter automatic For “Roller shutter control“, “Type of automatic: internal automatic“ has been selected. Outdoor temperature block Use outdoor temperature block No • Yes If “Use outdoor temperature block: Yes“ has been selected: Use outdoor temperature block Yes Type of temperature input object 1 Bit • 16 Bit If “Type of temperature input 1 bit“ has been selected: Shading is permitted if bit is 0, and it is blocked if bit is 1. If “Type of temperature input 16 bit“ has been selected: Shading is blocked if the measured value is smaller than the threshold value, and it is permitted if the measured value is larger than the threshold value plus hysteresis. Threshold in 0.1°C -300 … 800 Hysteresis in 0.1°C 1 … 100 Send current blocking status No • Yes 29
Dawn control / time control Use dawn and time control • No • only dawn control • only time control • both (OR gating) If dawn control or time control or both are used: Type of dawn input object 1 Bit • 16 Bit If “Type of dawn input object 16 bit“ has been selected: Type of dawn input object 16 Bit Dawn threshold value in lux 1 … 1000 Switching delay 1 minute Send current dawn status No • Yes Time control is accomplished by a communication object. Release of indoor temperature Use indoor temperature release No • Yes If “Use indoor temperature release: Yes“ has been selected: Type of input object 1 bit • 16 bit • 16 bit target/actual temperature If “Type of input object 1 bit“ has been selected: Shading is permitted if bit is 1, and it is blocked if bit is 0. If “Type of input object 16 bit“ has been selected: Shading is permitted if the measured value is larger than or equal to the threshold, and it is blocked if the measured value is smaller than the threshold minus hysteresis. Threshold in 0.1°C -300 … 800 Hysteresis in 0.1°C 1 … 100 Send current block status No • Yes If “Type of input object 16 bit target/actual temperature“ has been selected: Shading is permitted if the measured value is larger than or equal to the target value plus the target-actual-difference, and it is blocked if the measured value is smaller than the target value plus the target-actual-difference minus hysteresis. The target value is provided by the communication object. Target-actual difference in 0.1 °C 1 … 100 Hysteresis in 0.1°C 1 … 100 Send current block status No • Yes Shading automatic Use shading automatic No • Yes 30
Page 1 and 2: KNX S-B4T-UP 230 V and KNX S-B4T-UP
Page 3 and 4: KNX S-B4T-UP • from software vers
Page 5 and 6: Current: Output: Inputs: Data outpu
Page 7 and 8: Installation and Commissioning Inst
Page 9 and 10: No. Name Function Flags DP type 21
Page 11 and 12: No. Name Function Flags DP type 86
Page 13 and 14: Setting of parameters General setti
Page 15 and 16: If “Accomplish reference run: Yes
Page 17 and 18: If “Use operating range limit: Ye
Page 19 and 20: In case of automatic operation afte
Page 21 and 22: Dawn control / time control Use daw
Page 23 and 24: Position of the sun is defined by
Page 25 and 26: Roller shutter control The setting
Page 27 and 28: Travel position for slave in % if i
Page 29: Change from manual to automatic Man
Page 35 and 36: Awning control The setting options
Page 37 and 38: Monitoring period for zero position
Page 39 and 40: In case of automatic operation afte
Page 41 and 42: Dawn control / time control Use daw
Page 45 and 46: Window control Use operating range
Page 47 and 48: (Zero position sensor at input 4 of
Page 49 and 50: Change from manual to automatic Man
Page 51 and 52: If “Use coercive ventilation: Yes
Page 53 and 54: If “Type of input object 1 bit“
Page 55 and 56: Inverted standard control mode In c
Page 57 and 58: Send value Send value every (only i
Page 59 and 60: Brightness encoder If “Bus functi
Page 61 and 62: Temperature sensor For the “Gener
Page 63 and 64: If “Threshold value standard per
Page 65 and 66: Zero position sensor master over bu

Structure of Actuator KNX S-B4T-UP 230 V AC - IQmarket

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?