Structure of Actuator KNX S-B4T-UP 230 V AC - IQmarket

More documents

Recommendations

Info

“Shading position learning object“. In case of sun, the automatic then moves to the learned position. Control of roller shutters For “General settings“, “Actuator controls roller shutter“ has been selected. Roller shutter drive mechanism This is to indicate the specific features of the connected drive mechanism. Exchange UP/DOWN No • Yes Runtime UP in sec 0 … 320 Runtime DOWN in sec 0 … 320 Pause time for direction change in 0.1 sec 0 … 100 Accomplish reference run No • Yes Send drive position after change No • Yes If “Accomplish reference run: Yes“ has been selected: in case of more than 1 … 255 runs before one auto. position operation The reference run is always accomplished in the direction of the safe position. If “Send drive position after change: Yes” has been selected: Transmission delay of the position in 0.1 sec 0 … 50 23
Roller shutter control The setting options correspond to those of blinds or awnings. Use operating range limit Behaviour in case of bus voltage breakdown Use monitoring of alarm and blocking objects No • Yes No action • Stop • UP-command • DOWN-command No • Yes Operating range limit The operating range limit is used in order to avoid that two units collide with each other (e.g. an awning and a window which is about to open). One of two drive mechanisms is prioritised and is parameterised as master and the other one as slave. By means of zero position sensors, both actuators know the own current status and the current status of the other one. This one is either “in a safe position“ or “not in a safe position“. The safe position is reached as soon as the drive mechanism is in a sector where a collision is not possible (for an awning, for example, this might be an extension of 0 to 30%). In order to report the safe position of the drive mechanism, either a zero position sensor (e.g. final position switch or light barrier) may be connected at input 4 (IN4) of the actuator KNX S-B4T-UP, or the actuator receives the message of its zero position sensor by the bus (see graphic in chapter “Connection options for zero position sensors”). Before the drive mechanism of the master actuator is moved, the slave actuator receives the command to move its drive mechanism to the safe position. As a 24
Page 1 and 2: KNX S-B4T-UP 230 V and KNX S-B4T-UP
Page 3 and 4: KNX S-B4T-UP • from software vers
Page 5 and 6: Current: Output: Inputs: Data outpu
Page 7 and 8: Installation and Commissioning Inst
Page 9 and 10: No. Name Function Flags DP type 21
Page 11 and 12: No. Name Function Flags DP type 86
Page 13 and 14: Setting of parameters General setti
Page 15 and 16: If “Accomplish reference run: Yes
Page 17 and 18: If “Use operating range limit: Ye
Page 19 and 20: In case of automatic operation afte
Page 21 and 22: Dawn control / time control Use daw
Page 23: Position of the sun is defined by
Page 27 and 28: Travel position for slave in % if i
Page 29 and 30: Change from manual to automatic Man
Page 33 and 34: Position of the sun is defined by
Page 35 and 36: Awning control The setting options
Page 37 and 38: Monitoring period for zero position
Page 39 and 40: In case of automatic operation afte
Page 43 and 44: Position of the sun is defined by
Page 45 and 46: Window control Use operating range
Page 47 and 48: (Zero position sensor at input 4 of
Page 49 and 50: Change from manual to automatic Man
Page 51 and 52: If “Use coercive ventilation: Yes
Page 53 and 54: If “Type of input object 1 bit“
Page 55 and 56: Inverted standard control mode In c
Page 57 and 58: Send value Send value every (only i
Page 59 and 60: Brightness encoder If “Bus functi
Page 61 and 62: Temperature sensor For the “Gener
Page 63 and 64: If “Threshold value standard per
Page 65 and 66: Zero position sensor master over bu

Structure of Actuator KNX S-B4T-UP 230 V AC - IQmarket

Create successful ePaper yourself

Delete template?

Save as template?