Casestudie Breakdown prediction Contell PILOT - Transumo

More documents

Recommendations

Info

xlswrite(strcat(path, 'Excel\', filename, '- Maxima'), [dailydate-693960, maxvector, maxdaytime, maxnighttime], 'Maxima', 'A2'); %Total Values totalmin = min(import.data(:,2)); totalmax = max(import.data(:,2)); %-----Mean, Median, Mode, Standard Deviation----- %(Use interpolated data) %Create Date Vector interpolateddailydate = floor(interpolation(start,1) + second);; %create Mean Vectors meanvector = []; meandaytime = []; meannighttime = []; %create Median Vectors medianvector = []; mediandaytime = []; mediannighttime = []; %create Mode Vectors modevector = []; modedaytime = []; modenighttime = []; %create Standard Deviation Vectors stdvector = []; stddaytime = []; stdnighttime = []; %Create Vectors for Number of Dooropenings dailydooropenings = []; daytimedooropenings = []; nighttimedooropenings = []; %Auxiliary Variables startposition = start; jumplength = 0; for i = startposition:length(interpolation); if isequal(floor(interpolation(startposition,1) + second), floor(interpolation(i,1) + second)); jumplength = jumplength + 1; else %This is called, when date changes... interpolateddailydate = [interpolateddailydate; floor(interpolation(i,1) + second)]; %Vectors for Daily Values (Mean, Median, Mode, Standard Deviation) meanvector = [meanvector; mean(interpolation(startposition:startposition + jumplength - 1,2))]; medianvector = [medianvector; median(interpolation(startposition:startposition + jumplength - 1,2))]; modevector = [modevector; mode(interpolation(startposition:startposition + jumplength - 1,2))]; stdvector = [stdvector; std(interpolation(startposition:startposition + jumplength - 1,2))]; A-118
%Count Dooropenings per Day dailydooropenings = [dailydooropenings; sum(interpolation(startposition:startposition + jumplength - 1,3))]; %Compute Day- and Nighttime Values %(Mean, Median, Mode, Standard Deviation) nighttemp = []; daytemp = []; for j= startposition:startposition + jumplength - 1; if (mod(interpolation(j,1) + second, 1) >= daybegin) && (mod(interpolation(j,1) + second, 1)
Page 1 and 2:
Technische Universität Braunschwei
Page 3 and 4:
4.4 Review of Current State of Rese
Page 5 and 6:
Index of Tables Table 2-1: Error of
Page 7 and 8:
1 Introduction 1.1 Initial Position
Page 9 and 10:
2 Sensor Based Temperature Monitori
Page 11 and 12:
compressor. They are served by a ce
Page 13 and 14:
the specified value, it works very
Page 15 and 16:
of this, over a hundred irregular p
Page 17 and 18:
a centralized one. An isolated appl
Page 19 and 20:
Figure 2-8: Lack of Information Pro
Page 21 and 22:
Moreover, the fridge’s filling le
Page 23 and 24:
store this kind of data but only of
Page 25 and 26:
3 Current Monitoring Systems The la
Page 27 and 28:
device’s condition. Especially th
Page 29 and 30:
a converter that is also available
Page 31 and 32:
To indicate important events within
Page 33 and 34:
1. Display stored data in table for
Page 35 and 36:
This way of visualizing data is the
Page 37 and 38:
free text. Moreover it is possible
Page 39 and 40:
dependent limit and delay settings,
Page 41 and 42:
Aside from these functions, the kin
Page 43 and 44:
1. Temperature verification in retr
Page 45 and 46:
alarms by the use of additionally a
Page 47 and 48:
The third mentioned Centron Environ
Page 49 and 50:
4 Current State of Research As alre
Page 51 and 52:
even this improvement is still face
Page 53 and 54:
Another current approach is regress
Page 55 and 56:
S o n 2 = ∑ Yi −Yi n −1 i= 2
Page 57 and 58:
This algorithm returns an upper and
Page 59 and 60:
• Critical values • Pre-warning
Page 61 and 62:
5 Possible and Promising Ways of Da
Page 63 and 64:
could be: “The mean increase of a
Page 65 and 66:
The mode is the most frequent value
Page 67 and 68:
Figure 5-1: Two Samples of Regressi
Page 69 and 70:
5.4.2 The Major Problems of Regress
Page 71 and 72:
The next section will introduce tim
Page 73 and 74: explained in section 5.4. If such a
Page 75 and 76: pictured in Formula 5-12. Beside a
Page 77 and 78: P ( m) = P ( r ) ⋅ P ( m−r ) wi
Page 79 and 80: But the greatest problem is again t
Page 81 and 82: clustering as well as an analysis o
Page 83 and 84: The general idea of supervised lear
Page 85 and 86: sometimes data of a door opening se
Page 87 and 88: Beside the introduced notification
Page 89 and 90: A classification could be achieved
Page 91 and 92: Table 5-1: Estimated Improvements A
Page 93 and 94: As all these software products fail
Page 95 and 96: 6.2 Case Study The UMC St. Radboud
Page 97 and 98: Figure 6-3: Maximum Values at Dayti
Page 99 and 100: Figure 6-5: Minimum Values at Dayti
Page 101 and 102: Figure 6-9: Standard Deviation at D
Page 103 and 104: Table 6-3: Reported Notifications (
Page 105 and 106: Important for the determination of
Page 107 and 108: Remarkable is a comparison to the a
Page 109 and 110: Interviews with several employees f
Page 111 and 112: 7 Summary Cooling devices within me
Page 113 and 114: Bibliography Books and Articles: [B
Page 115 and 116: [Wittenberg98] Reinhard Wittenberg,
Page 117 and 118: Appendix 1 - Implementation of Inte
Page 119 and 120: %Name and location of the source fi
Page 121 and 122: Appendix 2 - Implementation of Stat
Page 123: dailydate = [dailydate; floor(date(
Page 127 and 128: xlswrite(strcat(path, 'Excel\', fil
Page 129 and 130: print('-dtiff', strcat(path, 'Graph
Page 131 and 132: ar([dailydate(1):dailydate(length(s
Page 133 and 134: Appendix 3 - Implementation of Data
Page 135 and 136: Duration = 0; maxtemp = 0; elseif (
Page 137 and 138: %Contains [Duration, Number of Occu
Page 139 and 140: disp(strcat('Dooropening
show all

Casestudie Breakdown prediction Contell PILOT - Transumo

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?