F-1⢠Installation Manual - Viking Access
F-1⢠Installation Manual - Viking Access
F-1⢠Installation Manual - Viking Access
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
SPECIAL FEATURES<br />
2<br />
1<br />
COM<br />
N.C.<br />
Motor Sensor<br />
Motor Sensor<br />
Low Battery<br />
. Lock<br />
Mag.<br />
Lock<br />
Obstruction<br />
Sensor Center Safety UL Radio<br />
Charger<br />
Loop Loop Sensor Rec.<br />
Power<br />
Charger<br />
Mag.<br />
Lock<br />
Mag.<br />
Lock<br />
Off 1 Center<br />
Loop<br />
Safety<br />
Loop<br />
UL<br />
Sens<br />
Radio<br />
Rec.<br />
off<br />
1sec<br />
Fail Safe/Fail Secure Operation<br />
The gate operator contains a unique design that<br />
Low Battery<br />
allows the user to move the gate manually in case<br />
Power<br />
of power failure.<br />
Radio<br />
Rec.<br />
UL<br />
Sensor<br />
Safety<br />
Loop<br />
Center<br />
Loop<br />
30sec<br />
30<br />
Hold Open<br />
Timer<br />
MAX<br />
60sec<br />
60<br />
Hold Open<br />
Timer<br />
min.<br />
min. MAX<br />
Hold Open<br />
Timer<br />
Obstruction<br />
Sensor<br />
Obstruction<br />
Sensor<br />
Open<br />
Open<br />
Limit<br />
0<br />
0<br />
Overlap<br />
p Delay<br />
Open<br />
1.5<br />
1.5<br />
Connection Locations<br />
OPEN RIGHT<br />
Fail Safe:<br />
By removing the wire-jumper plug<br />
from the “Fail Safe/Secure” connector:<br />
The gate can be moved with use of an<br />
elbow arm manually with a relatively low<br />
amount of force.<br />
Fail Secure:<br />
This unit is shipped with the default fail<br />
secure feature.<br />
1<br />
OPEN LEFT<br />
Fail Safe/Secure Fail<br />
Safe/Secure<br />
+28v<br />
Gnd<br />
Motor Sensor<br />
Low Battery<br />
+28v<br />
Radio Station Loop Connector Open Commands Guard Station<br />
Radio Station<br />
N.O.<br />
Mag. Lock<br />
of time, prior to closing N.C. automatically.<br />
Low Battery<br />
Power<br />
Mag.<br />
Lock<br />
Radio<br />
Hold Open Timer<br />
The Hold Open Timer function holds the gate at<br />
the open position COM for a predetermined amount<br />
Gnd<br />
+28v<br />
Gnd<br />
UL<br />
Safety Connector<br />
Obstruction<br />
Sensor Center Safety UL Radio<br />
Charger<br />
Loop Loop Sensor Rec.<br />
Power<br />
Charger<br />
Mag.<br />
Lock<br />
Radio<br />
Rec.<br />
UL<br />
Sensor<br />
Gnd<br />
Reopen<br />
Safety<br />
Loop<br />
Gnd<br />
Center<br />
Gnd<br />
Off 1 Center<br />
Loop<br />
Safety<br />
Loop<br />
UL<br />
Sens<br />
Radio<br />
Rec.<br />
Set the Timer to the desired time, from 1 to<br />
60 seconds.<br />
Mag.<br />
If this feature is not needed, Lock turn the Trim<br />
Pot clockwise to the “off” position.<br />
Note: The Hold Open Timer affects the “radio<br />
receiver command” Motor Sensor and the sequence of<br />
operation for the gate (see page 23).<br />
2<br />
Center<br />
Loop<br />
off<br />
1sec<br />
Exit<br />
30sec<br />
30<br />
Open Commands<br />
Hold Open<br />
Timer<br />
MAX<br />
Gnd<br />
min.<br />
Strike<br />
60sec<br />
60<br />
Hold Open<br />
Timer<br />
min. MAX<br />
Hold Open<br />
Timer<br />
Obstruction<br />
Sensor<br />
Obstruction<br />
Sensor<br />
Gnd<br />
Fire<br />
Open<br />
Gnd<br />
uard Station<br />
Close Stop Open<br />
Limit<br />
0 3<br />
0<br />
Open<br />
1.5<br />
1.5<br />
3<br />
Overlap Delay<br />
Overlap Delay<br />
Open<br />
Stop<br />
Overlap<br />
Delay<br />
Stop<br />
Stop<br />
Close<br />
Close<br />
Limit<br />
GND<br />
Close<br />
OPEN<br />
TECHNICAL SUPPORT 1 800 908 0884 29<br />
OPEN
Change language